This pilot light lens is red and is well under an inch long.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Cooktop.
This part works with the following products:
Jenn-Air, Kenmore.
Part# WPY700631 replaces these:
AP6024211, 7-0631, 700631, Y700631
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Infinite Switch failed, burner would not heat
Removed two screws holding 4-switch panel, drew a simple diagram to assure placement of wires on correct terminals, removed and replaced switch.
Switch works fine, but original knob does not fit shaft of replacement switch. Will try to order new knob, but it probably won't match the old knobs, so range will have one new knob & three old ones. I wish the order page noted that new knobs must be ordered to fit the new style shaft.
surface unit infinite switch needed replaced. The knobs and lens were cosmetic.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires and replaced the connections in sequence. It was easy. BUT, be sure the circuit breaker is disconnected if you want to enjoy the fruits of your labor. I figure I saved about $1100 by not having to buy a new stove top and I now have an almost new one. The cook appreciates it too.
removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.
Other Parts Used:
Dennis from Mahomet, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
age & solivents melted the on pilot light lens
removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.
Other Parts Used:
JAMES from McALESTER, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
LUC
January 27, 2022
IT LOOKS LIKE THE JENN AIR COUNTERTOP ELECTRIC STOVE INDICATOR LIGHT LENS THAT YOU ARE ADVERTISING IS THE LONG NECKED TYPE. DO YOU HAVE ANY OF THE SHORT ONES FOUND ON EARLIER MODELS USING THE SAME BASE ASSEMBLY???
THANKS
For model number JENN AIR COUNTERTOP
Hi Luc,
Thank you for your question. Before we can verify if the indicator light is available, we will need the model number from your range. We have included a link on where to locate the model number on your countertop stove. If you could resubmit your question with this information, we would be happy to help you. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
This grease filter is almost fourteen inches long and almost twelve inches wide. This filter is intended for use with some downdraft cooktops and ranges.
This surface burner knob is two inches in diameter. It is a black knob with a chrome trim, and white numbering denoting the temperature level of the surface burner. Sold individually. This knob accepts a D-shaped shaft.
