Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Arlene V - November 30, 2018
Verified Purchase
easy repair
The metal shield is a different size than the old part( smaller). I had to put a washer to cover the hole in the back of the oven . Other wise easy to install.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Getting F 1 and 2 error codes and the oven turned itself off.
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.
Other Parts Used:
Suzanne from Acton, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
75 of 143 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gene
April 26, 2018
Will this part fix my problem---push bake button and set temp. To 325 or any temp. 100 appears in the dial, but before it even gets to 100 it shuts off---repeat this same procedure many times and maybe you can finally get it to the temp you want and have set. It does this most of the time, but occasionally it will go up to the set temp on first try.
For model number ARDS800ww
Hello Gene, thank you for your question. The first part I would recommend replacing is the temperature sensor. That is the most likely issue. If the sensor is not working it will not read the temperature correctly and not allow the unit to heat. The sensor can be tested before ordering. The only other part that could be faulty is the electronic board. If the sensor does not fix the issue, the oven control board is the faulty part. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
February 6, 2018
The stove panel indicates a temperature of 350 degrees for the oven. However I checked the oven temperature with an oven thermometer and the actual temperature is 312 degrees. Will replacing the oven temperature sensor correct this, or should we continue to make adjustments to compensate? Thank you.
For model number ARR6400WW
Hi Jim, Thank you for the question. Yes if the oven is not reaching or is going over the correct set temperature, replacing the Oven Temperature Sensor should fix the issue. Good luck with the repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
December 28, 2021
How do I test the oven temperature sensor? Oven temp is 50F to 75 F below setting on thermostat, but will sometimes reach the set temperature, especially if set higher.
For model number ARTC7121WW
Hi Tim,
Thank you for your question. To test the sensor, you will need to reference your owner’s manual to determine what the correct reading should be for your model, as this varies from model to model. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. The reading should be approximately 1080-1090 ohms. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. We hope this helps! If you have any questions, please let us know.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Linda
July 31, 2019
I have just moved into a house with a selfclean Whirlpool wall oven. It looked as though they ran the clean cycle before the previous owners left but when i tried to use it would not heat with bake or broil. I replaced the thermal heat fuse and both elements worked just once, then the next time i tried to use the oven their was no heat again.
For model number GBS277PRQ01
Hi Linda, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
November 29, 2017
My ex is renting out her house and the temp sensor code sounds on the lower oven. It is built into the wall and cannot be moved out without taking the cabinet apart. What is the best way to replace... pull out oven cavity from oven or tear unit out from wall?
For model number AOGD2750WW-P1132529NWW
Hi Jerry,
Thank you for your question. You do not have to remove your appliance to replace this part. Here is a video that will show you how it is done: https://youtu.be/2IU_H0yrg-c . Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Marcy
November 24, 2017
Stove flashes F4 when you turn it on.
For model number AOCS2740WM
Hi Marcy,
Thank you for your question. That F4 error code indicates that your oven temperature sensor has failed and needs to be replaced. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Brian
November 30, 2019
Can not set temp, shows over 900
For model number Arts6650ww
Hi Brian, if everything else works sounds like a faulty temp sensor. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Marye
May 20, 2022
I need a heat sensor please
For model number 91195351590
Hello Marye, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS235718. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
