Part Location Diagram of WPW10653840 Whirlpool Door Latch - Black
See part 4 in the diagram
Replacing your Whirlpool Dishwasher Door Latch - Black
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Door Latch - Black

★★★★★
★★★★★
10 Reviews
$46.64
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11756967
Manufacturer Part Number WPW10653840
Manufactured by Whirlpool
Part Videos

Replacing your Whirlpool Dishwasher Door Latch - Black

Replacing your Whirlpool Dishwasher Door Latch - Black
Troubleshooting
This part fixes the following symptoms:
Door latch failure | Door won’t close | Will Not Start | Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, KitchenAid, Kenmore, Maytag.
Part# WPW10653840 replaces these:
AP6023622, W10574864, W10653840
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
10 Reviews
4.9
Filter By Rating:
  • 5 Stars
    9
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.1 / 5.0, 5 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Door would not latch shut
Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.
Other Parts Used:
  • RONALD from PRESCOTT, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch wouldn't close
Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.
Other Parts Used:
  • Colin from Goffstown, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Other Parts Used:
  • Edna from WEST MONROE, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door stopped latching properly.
Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
Other Parts Used:
  • Bryca from TULSA, OK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking around door and latch mechanisim seems to have failed
Still not sure it is repaired. Still have water leakage around upper edge of door on control data panel. We just experienced an issue with the auto drain system, the first since door seal repair and door latch replacement???? Is the latching mechanism suppose to secure the door?
If so it isn't?
Not a great success story. A new washer may be in the cards
Other Parts Used:
Dishwasher Door Seal
  • Robert from PORT LUDLOW, WA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

38 questions answered by our experts.
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Everett
January 14, 2019
When trying to start this Maytag dishwasher, model # mdb4949sdm, that was purchased on 2/2/2017,all the lights on the front panel start flashing. The door does not appear to be securing as well as it was before this happened, and there is no external handle. Do you think that the door latch has become defective in this situation. I have checked the "tab" that the latch connects to and it appears to be ok.
For model number MDB4949SDM
PartSelect logo
Hello Everett, Thank you for the question. The light blinking sequence will indicate which part or parts on your Maytag dishwasher need to be replaced or checked. If you can watch the lights and let us know the sequence we will be happy to take a look and see what part might be defective. Thank you for your inquiry, good luck with this repair!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Synithia
April 22, 2018
The door will not stay shut. To get the dishes done, i put a heavy chair in front of the door to keep to keep it closed. Is this the part needed to fix this issue?
For model number KDFE104DSS2
PartSelect logo
Hi Synithia, Thank you for your question. Yes, if your latch is the part that is causing you any issues then it would probably need to be replaced. You could take a quick look at your catch as well. The metal piece that the latch clips into. Just check to see if it is damaged at all. I hope that helps. Good luck with your repair.

5 people found this helpful.

Was this helpful?
Thank you for voting!
John
February 15, 2018
I went to start this dishwasher this morning after closing the door and I noticed there were no lights on the control panel and it did not respond to pushing the start button. I checked the circuit breakers and all indications that the washer is receiving power.
For model number KDFE104DSS2
PartSelect logo
Hi John, Thank you for your question. If the dishwasher is not starting, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door latch, the strike, the door balance link kit, the turbidity sensor, the motor and the electronic control board. I hope this helps. Thank you and have a great day!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Brandon
February 26, 2019
All the buttons on control panel work except for the start button. I can hit the cancel drain button and it will drain, but i cant get the start button to work. Do i need to replace the control panel?
For model number MDB4709PAB4
PartSelect logo
Hello Brandon, thank you for your question. I would recommend testing the latch switches before ordering the panel. If the start button is lit up but the unit won't start, the latch switches may not be functioning properly. These switches, when activated, tell the unit that its ok to start the wash cycle. If the switches are not the issue, then the control panel would be the next step. I hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
SHAWN
December 5, 2018
My door catch is stuck in the latch #1 is there a lock? #2 i have ordered the latch since the catch seem to be still useable to replace the latch do i just remove the torques head screws on the panel covering it? Thank you
For model number WDTA50SAHB0
PartSelect logo
Hello Shawn, Thank you for the question. Yes, the latch has a lock that will hold the catch. To replace the Latch you will need to remove the door panel. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Brian
March 6, 2019
Wont start. Flashing no particular sequence and door wont latch. When start is pushed and door closed it will flash over 25 times with no sequence.No attempt to latch.
For model number mdb4949sdm2
PartSelect logo
Hello Brian, thank you for your question. It sounds like the latch has failed. If the latch doesn't engage the dishwasher will not start. We would recommend replacing the door latch first to see if that fixes the issue. I hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Ivan
July 4, 2019
My internet searches have produced inconsistent results. Whirlpool wdt780saem2 will not start. Some searches say the door latch is the problem, others it is the door balance kit. I have the latch out and there seems to be no continuity through the switch when the latch is closed. Tells me the latch is the problem. Does this sound correct to you?
For model number WDT780SAEM2
PartSelect logo
Hello Ivan, thank you for writing. When testing the Door Latch with a multi meter it should read as zero when functioning properly. If it reads higher than zero then the switch is faulty and should be replaced. For this symptom you will want to consider either the Door Balance Link Kit part PS972325 or the Pump Motor part PS11773089 for your model. We hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
William
February 20, 2023
the plastic pull handle broke on dish washer, do i have to buy the whole handle assembly to replace or can i buy just the pull part that pulls the door open
For model number 665 13099n41
PartSelect logo
Hi William, thank you for your question. You buy only the handle, part number PS3494613. We hope this information is helpful!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Tom
July 31, 2018
Can a faulty door latch cause the rinse aid to not dispense? I think the latch is cracked or broken. When opening the door, the seam between the door and the control panel expands and then closes back to normal after the door is open. The opening is about 1/16". The screws holding the latch in place are tight. Thanks in advance for your thoughts!
For model number KUDS30IXWHA
PartSelect logo
Hello Tom, Thank you for the question. The latch does not control the dispenser. The dispenser has a small red wax motor on the back that tells the dispenser to open and release the detergent or the rinse aid. If the rinse aid cap is not opening, you may need to have the dispenser replaced. You can also remove and check the rinse aid cap to see if there has been any wear or damage that would prevent it from opening. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Scott
August 1, 2018
I noticed the wrong cycle had been selected, so i stopped and reset the program. Once it reset all the lights went out and now the control panel is non-responsive to touch and does not light up. What might the cause and fix be?
For model number KUDS30IXBLA
PartSelect logo
Hi Scott, Thank you for your question. Try cutting power to the dishwasher for 5 minutes and turning it back on. If this does not help, you may need to test the electronic control board with a multimeter to see if it is working correctly. If the dishwasher will still not start, some other parts that you will need check are the pump, the sump and motor assembly, the capacitor, the door latch, the turbidity sensor and the touchpad. I hope this helps. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
;
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11756967
Manufacturer Part Number: WPW10653840
Brand
Model Number
Description
Kenmore
66512413N410
Dishwasher - DISHWASHER
Kenmore
66512413N411
Dishwasher - DISHWASHER
Kenmore
66512413N412
Dishwasher - DISHWASHER
Kenmore
66512723K311
Dishwasher - DISHWASHER
Kenmore
66512762K312
Dishwasher - Dishwasher
Kenmore
66512762K313
Dishwasher - Dishwasher
Kenmore
66512763K313
Dishwasher - Dishwasher
Kenmore
66512769K313
Dishwasher - Dishwasher
Kenmore
66512772K311
Dishwasher - Kenmore Dishwasher Model 665.12772K311 (66512772K311, 665 12772K311) Parts
Kenmore
66512773K311
Dishwasher - Kenmore Dishwasher Model 665.12773K311 (66512773K311, 665 12773K311) Parts
Kenmore
66512773K313
Dishwasher - Dishwasher
Kenmore
66512773K314
Dishwasher - Dishwasher
Kenmore
66512774K311
Dishwasher - Kenmore Dishwasher Model 665.12774K311 (66512774K311, 665 12774K311) Parts
Kenmore
66512776K311
Dishwasher - Kenmore Dishwasher Model 665.12776K311 (66512776K311, 665 12776K311) Parts
Kenmore
66512779K311
Dishwasher - Kenmore Dishwasher Model 665.12779K311 (66512779K311, 665 12779K311) Parts
Kenmore
66512782K311
Dishwasher - Kenmore Dishwasher Model 665.12782K311 (66512782K311, 665 12782K311) Parts
Kenmore
66512782K312
Dishwasher - Dishwasher
Kenmore
66512782K313
Dishwasher - Dishwasher
Kenmore
66512783K311
Dishwasher - Undercounter Dishwasher
Kenmore
66512783K312
Dishwasher - Dishwasher
Kenmore
66512783K313
Dishwasher - Dishwasher
Kenmore
66512789K311
Dishwasher - Kenmore Dishwasher Model 665.12789K311 (66512789K311, 665 12789K311) Parts
Kenmore
66512789K312
Dishwasher - Dishwasher
Kenmore
66512789K313
Dishwasher - Dishwasher
Kenmore
66512793K312
Dishwasher - Dishwasher
Kenmore
66512793K313
Dishwasher - Dishwasher
Kenmore
66512833K311
Dishwasher - Kenmore Dishwasher Model 665.12833K311 (66512833K311, 665 12833K311) Parts
Kenmore
66513032K115
Dishwasher - DISHWASHER
Kenmore
66513032K116
Dishwasher - DISHWASHER
Kenmore
66513033K115
Dishwasher - DISHWASHER
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service