Part Location Diagram of WPW10512946 Whirlpool Roller Support Tri-Ring
See part 20 in the diagram
Replacing your Kenmore Dryer Roller Support Tri-Ring
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Roller Support Tri-Ring

★★★★★
★★★★★
3 Reviews
$17.11
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11755850
Manufacturer Part Number WPW10512946
Manufactured by Whirlpool
Product Description

Roller Support Tri-Ring Specifications

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Kenmore Dryer Roller Support Tri-Ring

Replacing your Kenmore Dryer Roller Support Tri-Ring
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Kenmore, Whirlpool, Maytag, KitchenAid.
Part# WPW10512946 replaces these:
AP6022517, 339491, 339941, 4319305, 690997, W10512946, WPW10512946VP
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.3
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.9 / 5.0, 15 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Other Parts Used:
Dryer Drum Support Roller Drum Support Shaft - Rear Shaft with Right Hand Threads WASHER
  • John from Tucson, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
41 of 60 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud sreeching and vibration
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Other Parts Used:
Dryer Drum Support Roller Thrust Washer Drive Belt Idler Pulley
  • Robert from TUTTLE, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drum very loud when rotating
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and replaced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Other Parts Used:
Rear Drum Support Roller Kit
  • michael from indianapolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
13 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the drum support rollers was worn out
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Rear Drum Support Roller Kit
  • David from Fleetwood, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bad drum rooller bearing
took the top, sides and back removed the drum and replaced the roller roller shaft and drive belt and the belt tensioner
Other Parts Used:
Drum Roller Shaft - Left Side Support Roller Clip BRACKET Rear Drum Support Roller Kit Roller Shaft Washer
  • randy from simi valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
10 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
parts took more than two months to get here.
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Other Parts Used:
Drum Support Shaft - Rear Shaft with Right Hand Threads Drum Support Roller Shaft - Right Hand Threads Dryer Drum Support Roller
  • rodney from Mad River, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer was making a squeaking sound when running
Installation went very well. Raised the top of the dryer, removed the front of the dryer, remove the drum, at this point the dryer‘s wide open removed the police and the tensioner also remove your tire rings replace everything back in order as how are you get apart. Repair took about an hour and 15 minutes
Other Parts Used:
Maintenance Kit Rear Drum Support Roller Kit
  • David from PATASKALA, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High pitch noice
Raised the front of top panel with the putty knife and the front panel was unscrewed as the video showed. The drum slid out after the belt was released.

My machine had 4 rollers, which was not shown in the schematics. So I replaced the back, cleaned the front ones and works great for now. Plan to replace the front later.

Removing the tri rings is much easier if cut w wire cutters. Otherwise waist lots of time to get them off. Just buy new ones.
Other Parts Used:
Dryer Lint Screen Grille Dryer Drum Support Roller
  • Luis from FRESNO, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would run 1 min then stop running with some heat in drum
Videos are excellent to open and access internal parts. It turned out a rat was killed in the blower fan when we first encountered the problem. This prevented the blower from turning which interfered with motor function.

This required removing drum & belt, disconnecting motor clips, blower belt, and blower housing. The blower housing needed to be disassembled. Having a 5/16” & 1/8” ratcheting nut driver makes this process much easier. Don’t try this with a wrench.

After getting rid of the rat and decomposition, we sanitized the entire housing with soap & chlorine bleach.

Reassembly was uneventful and relatively easy. We ended up replacing 4 rollers, 2 belts (drum belt & blower belt), the thermistor which was damaged as a result of the blocked blower.
Other Parts Used:
Dryer Drum Support Roller Thermostat, Internal-Bias Drum Drive Belt Moisture Sensor
  • Bob from CHULA VISTA, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
7 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer was squeaking and would not heat at all.
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Other Parts Used:
Rear Drum Support Roller Kit Drum Roller Shaft - Left Side Drum Support Roller Shaft - Right Side
  • Steven from Oxnard, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

4 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
January 2, 2019
I have plenty of heat and the dryer tumbles, but there is no air coming out of the exhaust hole in the back? Clothes take way too long to dry and water is pooling under the dryer. Any ideas? Thanks!!
For model number MEDB200VQ0 Maytag Clothes Dryer
PartSelect logo
Hi Robert, Thank you for your question. If there is no air coming out of the exhaust, then there is likely a blockage of lint trapped in the vent that will need to be cleaned out to correct this issue. I hope this helps. Thank you and have a great day!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Jonathan
March 2, 2020
Dryer gets hot but want tumble
For model number Leb6200pq0
PartSelect logo
Hello Jonathan, Thank you for the question. In most cases this is caused by a broken Belt. We hope this helps.

4 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Lisa
March 3, 2023
My dryer is very noisy and sounds like it is grinding as the dryer is drying the clothes. I know that it must be the parts that turn the drum that are worn, I just need to know what parts I will need and how many to fix this problem if someone could assist me I would be very appreciative.
For model number 110.61633610
PartSelect logo
Hi Lisa, thank you for reaching out. According to our research, you need to check the following parts to fix the issue: the drum roller, part number PS11752609, and the idler pulley, part number PS334244, and the roller support tri-ring, part number PS11755850. We hope this sorts out your problem!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Steve B
September 2, 2019
Is the price listed for one tri ring? From the video it would appear I need two tri rings per wheel? Is it really that much for one tri ring? I will be ordering one drum support roller (ps11752609). Thanks.
For model number Whirlpool Dryer
PartSelect logo
Hello Steve, Thank you for the question. The Tri Ring is sold individually. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11755850
Manufacturer Part Number: WPW10512946
Brand
Model Number
Description
Kenmore
10686294140
Dryer
Kenmore
10686294340
Dryer
Kenmore
10686294540
Dryer
Kenmore
10686294740
Dryer
Kenmore
10686294840
Dryer
Kenmore
10687884100
Dryer
Kenmore
10687884300
Dryer
Kenmore
10687884600
Dryer
Kenmore
10688419100
Dryer
Kenmore
10688419300
Dryer
Kenmore
110088732791
Washer Dryer Combo
Kenmore
1101820299
Washer Dryer Combo - WASHER DRYER LAUNDRY SYSTEM
Kenmore
11060012000
Dryer
Kenmore
11060012001
Dryer
Kenmore
11060012002
Dryer
Kenmore
11060022010
Dryer
Kenmore
11060052990
Dryer
Kenmore
11060052991
Dryer
Kenmore
11060056990
Dryer
Kenmore
11060056991
Dryer
Kenmore
11060072990
Dryer
Kenmore
11060072991
Dryer
Kenmore
11060092990
Dryer
Kenmore
11060092991
Dryer
Kenmore
11060094990
Dryer
Kenmore
11060094991
Dryer
Kenmore
11060096990
Dryer
Kenmore
11060096991
Dryer
Kenmore
11060097990
Dryer
Kenmore
1106012510
Dryer - ELECTRIC DRYER
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service