We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Don
November 26, 2017
I need just the door for the soap dispenser
For model number IUD8500BX1
Hello Don, Thank you for the question. The dispenser door is not sold separate from the full dispenser, PartSelect Number PS11752440. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Paula
December 28, 2017
My Kenmore dishwasher works perfectly...except the soap dispenser door won't open while the machine is cycling. i can open it manually. can you tell me from the exploded diagrams if the dispenser uses a wax solenoid, or a hinge pin or if the electric harness is what needs to be replaced to make the dispenser door open during wash cycles?
For model number 66515112K211
Hi Paula,
Thank you for your question. Yes it does use a wax motor. It is likely that you would have to replace your dispenser to fix that issue. I hope that helps. Good luck with your repair.
I can open the dispenser manually but when I used the soap pad it remains in the dispenser which would indicate that the dispenser did not open and if I used liquid soap there is like a plastic mass of cake like substance remains. What could be the cause?. thank you.
For model number 665.13803N710
Hello Sheldon, Thank you for the question. This sounds like the Wax Motor on the back of the dispenser is defective and not opening the dispenser. In this case the dispenser would need to be replaced, PartSelect Number PS11754645. Hope this helps!
The soap dispenser opens 2 minutes into wash cycle!
For model number KUDC10FXSS5
Hello Jim and thank you for writing.
For your convenience, we have attached the link to your manual with repair instruction. We hope this helps. Good luck with your repair.
https://partselectcom.azureedge.net/assets/manuals/4C8F4BE54C04D887FD454221505C30D17AE8E56A.pdf
1 person found this helpful.
Was this helpful?
Thank you for voting!
Stefanie
December 11, 2018
I need to replace the soap dispenser on Maytag model# MDBH949PAB4. Do you need to replace the mounting bracket as well?
For model number MDBH949PAB4
Hello Stefanie, Thank you for the question. If the bracket is not damaged, the original bracket can be reused with the new dispenser. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Virna
February 5, 2019
The dishwasher started leaking by the lower right corner of the door. I see that it only leaks when dispensing the soap as the water has soap on it. When rinsing, i do not see the same leakage. Can you help me find the possible problem? I am planning to change the door gasket just to see if it helps. I order one from you. Thank you so much.
For model number MDB7749SBM3
Hello Virna, thank you for your question. It sounds like the bottom door seal needs to be replaced. When the soap is dispensed and runs down the door you're getting that leak. We would recommend replacing the door seal Part Number: PS11755651 to see if that fixes the issue. I hope this helps!
Was this helpful?
Thank you for voting!
Maureen
January 10, 2020
What part do i need if soap dispenser will not close?
For model number WDT710PAYM3
Hello Maureen,
Thank you for your question. Our sources suggest replacing the dispenser itself under part PS11750038 for your model to fix the issues. We hope this helps!
The actual dispenser is not closing tight and the soap is going everywhere. Is it called the dipenser mounting bracket?
For model number 665.13129k703
Hi David, thank you for reaching out. According to our research, you may need to check the following part to fix this issue: dispenser mounting bracket, part number PS11755103, and detergent shield, part number PS11746147. We hope this solves your problem!
Hello Ali, Thank you for your inquiry. If the door on your dispenser has broken, you will have to replace the entire dispenser. Hope this helps!
Was this helpful?
Thank you for voting!
Eric
March 19, 2018
My dishwasher wont dispense rinse aid leaving all dishes looking cloudy. What parts do I need?
For model number MDB8949SBM3
Hello Eric, Thank you for the question. You can check to make sure there is no build up not allowing the cap to pop open. If there is no build up then the dispenser is defective and will need to be replaced, Part Number: PS11752437. Hope this helps!
This part is a replacement screw for your dishwasher. It is made of metal and is approximately ¾ inch long. It is a hex-head screw and is sold individually. It is used to hold the dispenser bracket in place. This part is...
This detergent dispenser assembly is for dishwashers.
Detergent dispenser assembly holds the dishwasher detergent and rinses agent in covered compartments.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11755103
Manufacturer Part Number: WPW10462232
