Electronic Control

Good Day Robert. Thank you for your question in regards to your unit (Model Number MF12269VEW1). Based on our research you may need to replace the following part in your unit: Part Number WPW10310240. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.

Hello Michael, thank you for your question. If the main board has been replaced and is showing the P0000 error code, the board has to be programmed. The Program Code is usually located on the Serial number Plate on the unit, after the word Code. Check your owners manual for the programming process once you have this code! I hope this helps!

Hi William, Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the compressor start relay, the temperature control thermostat, the electronic control board, the compressor and the thermistor. I hope this helps. Thank you and have a great day!

Hi Yves, thank you for your question. When you are having temperature problems in your fridge, there are a few parts that could cause the issue. You can use a multi meter to test most of the parts. Make sure you cut power to your appliance before doing any repairs or tests. First you should test your defrost thermostat. Place the thermostat in ice cold water for 2-3 minutes after removing it from your appliance. It should be reading 0 ohms to be working correctly. Another part to check would be your defrost heater. Remove it from the appliance. It should be reading anywhere between 0 - 50 ohms to be working. You could check your temperature sensor. To find the correct reading for this part you will have to refer to your tech sheet that comes with your appliance. You can usually find this tech sheet behind the bottom grille of your fridge on either the right or left side. These are the most common parts that cause this issue in your appliance. So it is suggested you check them first. I hope that helps. Good luck with your repair.

Hi Melinda, Thank you for your question. It is suggested that you unplug your appliance for about 5 minutes. When you plug your appliance back in that should reset your board. If you are still experiencing a problem, you may have a loose wire connection or you may have to replace your control board. I hope that helps. Good luck with your repair.

Hi Mike, Thank you for your question. If the display lights up and then the refrigerator shuts down a few minutes later, there are some parts that you will need to check to see which one is causing the issue. You will need to check the evaporator fan motor, the damper control assembly, the thermistor, the temperature control board, the defrost thermostat and the main electronic control board. You will also need to check to see if the evaporator coils are frosted over as this can also cause the refrigerator shut down after a few minutes. We hope this helps. Thank you and have a great day!

Hi Thomas, Thank you for your question. If the display on the dispenser control board with touchpad is not responding, then you will need to use a multimeter to check the continuity of the touchpad, the dispenser electronic control board and the wiring connections between the 2 parts. You will also need to check the main electronic control board for the refrigerator as well to see if it is working correctly. If the refrigerator and freezer section are too warm I would also check the the capacitor and the thermistor. I hope this helps. Thank you and have a great day!

Hi Will, Thank you for your inquiry. If the refrigerator and freezer sections are not cooling then you will need to replace the capacitor, part number PS11757023. This part fixes the issue 99% of the time. I hope this helps. Thank you and have a great day!

Hi Willy, Thank you for your question. If the refrigerator is too cold and you have already replaced the damper, you will need to check the thermistor. I hope this helps. Thank you and have a great day!

Hello Sandra, Thank you for the question. This sounds like an issue with the Low Voltage Dispenser Control Board, PartSelect Number PS2069839 in the dispenser controls. I looked up the part and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!