Product Description
Terminal Block Specifications
It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Range Terminal Block
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Element will not heat | Little to no heat when baking | Touchpad does not respond
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo, Cooktop.
This part works with the following products:
Maytag, Amana, Whirlpool, Magic Chef.
Part# WPW10245259 replaces these:
AP6017673, 0306379, 0B00200399, 14253508, 14265221, 14277260, 1867-255, 1867255, 4364187, 5-50044, 5-50834, 550044, 550834, 7-90272, 7401P002-60, 7401P028-60, 7401P038-60, 7401P039-60, 790272, 8189776
...
Show more
, 880002, R0167038, W10245259, Y0306379, Y0B00200399
Show less
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Danielle R - December 20, 2019
Verified Purchase
Didn't solve the problem
Ordered this part as it was listed as a possible solution to an oven that wouldn't heat. The part was exactly as pictured and easy to replace but did not solve the problem. Waste of time.
Eric L - July 24, 2018
Verified Purchase
Terminal Block
It’s a terminal block. It terminates. Quick delivery. Thanks.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 5 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Other Parts Used:
-
Joseph from Decatur, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
91 of 197 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would heat up very slowly and not reach more than 325 *F
I purchased all the likely suspects. It was a corroded lower heating element that was faulty. Fixed the burnt out light bulb for good measure while I was in there.
Other Parts Used:
-
Andrew from BOTHELL, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
12 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Other Parts Used:
-
Peter from FREDERICK, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Other Parts Used:
-
Jared from UNION GROVE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Other Parts Used:
-
Larry from Scranton, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Preston
January 20, 2018
I went to use the cooktop one day and after turning on it started sparking and smoking from the back of the unit. I pulled the stove out and found the black wire at the terminal block had burned into it. Whoever installed the power cord did not tighten the nuts on the terminal block. Would this have caused the short or do you think something caused it and this was the weakest link so to speak? Also, do you think it damaged anything else? There is not any obvious damage or bare wires anywhere on the unit.
For model number MERH752CAS
Hello Preston,
Thanks for your question. This type of issue typically arises from loose wiring. I would recommend inspecting all of the range's wiring immediately to ensure nothing is damaged or still loose. Replace any wires that are damaged.
I hope this helps.
11 people found this helpful.
Was this helpful?
Thank you for voting!
Pat
June 12, 2019
In order to get the oven to heat i need to hold in on the start button. Is there a sensor which is kicking this out or is it the control board?
For model number ywfe510s0aw0
Hello Pat, thank you for your question. If the start button isn't working properly, and you have to hold the start button we would recommend testing oven thermostat PartSelect Number PS11749737 first. This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature.Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If that part measures within those readings, the electronic board should be replaced. I hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
February 11, 2018
After the power was off for 2 days the oven display was not responding on the stove.At all and the oven will not work at all what could be the reason and dos it need a part if so what part.
For model number AER5511AAW
Hello Tim, thank you for your question. If the top elements as well as the oven are not working, I would recommend changing the terminal block and perhaps the power cord to the unit. Also check the plug the appliance is plugged into to make sure the right voltage of power is coming to the unit. If the stove top burners are working but neither the baker OR the broil unit is working inside the oven section, the part you would need to replace is the Electronic Oven Control Board part number PS2357664. You may also want to check the Long Oven Sensor PS1570174. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Donald
August 15, 2017
Wife was using stove top and oven, and all power shut off. Will not restart. There is not a breaker in the panel for the stove. House built in 2014. Do i need to call an electrician or a repairman?
For model number WFE540H0AS0
Hi Donald,
For something like that you would have to contact a repair technician. It seems like the electronic control board on your appliance might have shorted out during your power outage. An appliance repair technician should be able to determine that for you without a problem. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
December 6, 2017
Oven works but induction top does not no lights or control
For model number WF1910H0AS0
Hi Robert,
Thank you for your question. There are some parts that you will need to check to see which one is causing the issue. You will need to check the terminal block, the oven sensor, the safety thermostat and the light socket. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jeff
December 16, 2017
I have no power to both top burners and oven although the light indicators are working as well as convection fan.
For model number JES8850AAB
Hello Jeff, Thank you for your inquiry. I would recommend checking your burner and oven elements, the infinite switches, the oven sensor, the terminal block and the oven control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Vincent Milack
September 19, 2019
The terminal block burned along with filter board (i think that is what it is called). I see you have the terminal block, but i can't seem to locate the filter board on your website. I may not have the correct name for the board. It's the little circuit board that sits between the terminal block and the associated wires. It's mentioned in the customer repair stores (joseph from decator, ga). Any assistance will be greatly appreciated. Vincent
For model number JMW9330DAB
Hello Vincent, thank you for your question. The noise filter board is PartSelect Number PS4239674. Please enter the part number into the site for current price and availability. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Denean
November 25, 2021
Burners and oven stopped heating during use. Screen was initially showing that both were on, then after resetting the breaker, screen went black. Screen will temporarily turn back on when I turn the burner dials, but neither burners nor oven will heat up. Does this sound like a terminal block issue?
For model number WFE775H0HV0
Hello Denean, thank you for your question. We feel it may be the terminal Block part PS11750972 or the Electronic Control part PS16555254. For more specialized assistance or to speak have a qualified technician look at the unit, we would suggest calling the manufacturer of the unit directly. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Brad
June 3, 2019
KitchenAid wall oven lost power, nothing to the control panel, light wont come on when door is open, breaker is fine. Any ideas?? terminal control or thermal fuse?
For model number KEBK101SS00
Hello Brad, thank you for writing. For this symptom you will want to consider either the Fuses, the Temperature Sensor, or the Electronic Control Board, but the model number you provided is a partial model number with multiple variations. Could you please provide the full model number so that we may look into the correct replacement parts? We look forward to hearing back from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Terri
March 1, 2024
My stove eyes will heat up. The panel will not light up so I can use the oven except the time will flash.
Any help would be much appreciated
Thanks
For model number ACR4303MMS0
Hello Terri, thank you for reaching out. Make sure that the wire connections to the control board are not faulty. If this is not the issue, then you may need to replace the oven control board, part number PS16555255, to solve the problem. Glad to be of assistance!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- 3
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11750972
Manufacturer Part Number: WPW10245259
Manufacturer Part Number: WPW10245259
Brand
Model Number
Description