Accumulator Filter

Take out the old parts and clean all the ones to be reused by power washing with garden hose and/or compressor blasting. Put it all back together. BE VERY CAREFUL NOT TO PUNCTURE THE ACCUMULATOR FILTER! THE TORX SCREWS ARE RIGHT NEXT TO THE FILTER SO IF YOU SLIP AND DROP THE TOOL, THE FILTER WILL BE TOAST!

THE DISHWASHER WORKS PERFECT NOW!

Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!

I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

Looks like Maytag knew this was a problem. My chopper sleeve (plastic) was stripped and causing the impeller to not spin. The replacement part was all metal and was very easy to replace the old one just by removing screws. The replacement looks to be very sturdy and should last a lot longer than the original. Thanks.

Removed the screws that held the spray arm. Remove dthe screws that held the flow filter flow plate assembly. Removed screw holding the impeller. Thoroughly cleaned all spray arms and associated tubing. Reassembled parts. Installed air gap assembly between dishwasher and garbage disposal (which I should have 4 years ago). Unit runs fine now.

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.