Average Repair Rating: 3.3 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Replacing still working but old and stained levers
The overflow grille was no problem. It just slides out. To get to the levers, you need to remove the front cover trim. Pay attention to where everything is before you remove parts and how the wiring is set up (over or under parts). There are two slots below the trim, use your blade screw driver and pop the trim. You'll notice that the 4 buttons for ice (crush - cube) and the light (off-on) are on that panel. I don't recall well, but I believe two screws (one at each side) hold that part in place. Once loose, I flipped it up, disconnected the white multi- wire quick connector and used duck tape to tape the panel to the door and keep it out of the way. Another screw keeps the levers in their place, with a metal element. Remove it and the levers will come out. The ice guide just snaps out from two sides and a middle plastic hook of the ice dispenser lever. Replace everything in reverse order. That's about what I remember. Hope it helps.
I replaced these parts mainly for aesthetic reasons and to prepare our home for a rental. I was very impressed with PartSelect's customer service and delivery. The part literally arrived the next day. Will definitely do business with them again.
To replace front cover and ice door kit I had to check the new cover how it is cliped on the bottom to remove the old cover, but after that it was not very difficult.
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Larnell
March 13, 2020
No water when from dispenser ice maker works fine
For model number ED2KVEXVL01
Hello Larnell, thank you for your question. We would recommend checking the control bracket and the micro switch first. The function of the control bracket part is to hold the micro switches and the light socket in the freezer dispenser section in place. If that part is broken or cracked it can cause issues. The micro switch helps activate the water valve to allow water to be dispensed. If those are not the issue, the water valve should be checked. I hope this helps.
Water is dripping from spout. How do you replace it ?
For model number 106 58502800
Hi Wanda,
Thank you for your question. It is normal for a small amount of water to drip from the spout after you have taken water from the dispenser. If it continues to leak long after you have dispensed water, then you may have air trapped in the water lines. To remove it, you will need to purge the water lines for a few minutes until it has cleared. If this does not resolve the issue, you will need to check the water pressure and the water inlet valve. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Jon
April 11, 2023
My water dispenser doesn't always completely shut off, and drips slowly. Will this part fix the problem with the shut off working correctly?
For model number 10656586500
Hi Jon, Thank you for writing. If the lever is loose, it will need to be replaced as it could be causing the leak. Good luck with the repair!
Was this helpful?
Thank you for voting!
Lavelle
April 16, 2023
Need new top door shelf.
For model number ED5PHEXMBOO
Hello Lavelle, thank you for writing. On the Refrigerator Door, under the Dairy Door, is the top Bin PS1173959. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
Mike
November 25, 2019
The water will not shut off from the water dispenser, is it the lever that is the problem or is something else that I need to replace?
For model number 106.58902802
Hello Mike, Thank you for the question. If the lever is not stuck or loose it should be fine. If there lever is good you can test the Micro Switch PartSelect Number PS11738948. Hope this helps!
This is a genuine Whirlpool dispenser overflow grille for your refrigerator. This part is made of plastic and snaps in under the water and ice dispensers on your refrigerator door. Its function is to catch drips and spil...
This is a genuine Whirlpool dispenser overflow grille for your refrigerator. This part is made of plastic and snaps in under the water and ice dispensers on your refrigerator door. Its function is to catch drips and spil...
This is a genuine Whirlpool dispenser overflow grille for your refrigerator. This part is made of plastic and snaps in under the water and ice dispensers on your refrigerator door. Its function is to catch drips and spil...
This is a genuine Whirlpool dispenser overflow grille for your refrigerator. This part is made of plastic and snaps in under the water and ice dispensers on your refrigerator door. Its function is to catch drips and spil...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11749101
Manufacturer Part Number: WPW10152858
