
Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 9pm EST
Refrigerator Pantry Drawer End Cap Right Side WPW10121977
Does this part fit my model?
Need help finding your model number?Refrigerator Pantry Drawer End Cap Right Side Specifications

How Buying OEM Parts Can Save You Time and Money
- < Prev
- 1
- 2
- 3
- Next >
- < Prev
- 1
- 2
- 3
- Next >
- < Prev
- 1
- Next >
The difficulty is in (1) noting and remembering how the assembly came off and apart. (2) Putting the moving parts inside of the end cap like they came out and (3) replacing the back and side at the same time. The back assembly has a clip that inserts to the left. It is important to insert that first. The side portion inserts by placing above the slots and pushing in (to the right) and down at the same time. It all comes together and you will wonder how you did it.
-
Robert from LA MESA, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Peter from EL CERRITO, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
There are no screws on the end caps for this model of fridge, unlike some YouTube videos you might see.
There's a release catch nearly in the middle of the cap. With your index finger, press down on the tab, to release the catch, while lifting the front of the end cap. The end cap should lift up and away from the side wall of your fridge.
Be careful to then rotate the entire assembly - in the case of the right side end cap - towards you, so that you can disengage the tab on the crisper drawer temp controller, that fits in the back wall of the fridge.
Once you've unhooked the control rods to the crisper temp. control, you'll need to remove the crisper drawer runners.
Again - on this model, there are no screws. The runners just slide out from underneath their retaining plastic tabs. Slide them towards what would be the front of the fringe if they were in their natural position, they clear the retaining tabs and become free.
The control rods need to be re-attached on the new end cap.. just take your time click it between the various plastic tab.
Then insert the end tab of the crisper temp control in the back wall, rotate the entire assembly 90 degrees, so the end cap is aligned with the slide wall, and lower it into position until the retailing clip clicks into position. Congratulations, you've replaced your right side end cap!
Then reinstall all the supports, shelves, bins etc. and you're good to go.
Good Luck!
-
Jon from HOUSTON, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
MARGARET from COUPEVILLE, WA
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Christine W from BAINBRIDGE IS, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
-
Mark from DAYTON, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Scott from NORFOLK, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
24 people found this helpful.
9 people found this helpful.

7 people found this helpful.
2 people found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: WPW10121977

Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 9pm EST