Part Location Diagram of WPW10074580 Whirlpool Agitator Cap Barrier with Seal
See part 2 in the diagram
Replacing your Whirlpool Washer Agitator Cap Barrier with Seal
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Agitator Cap Barrier with Seal

★★★★★
★★★★★
3 Reviews
$14.11
  In Stock
PartSelect Number PS11748113
Manufacturer Part Number WPW10074580
Manufactured by Whirlpool
Product Description

Agitator Cap Barrier with Seal Specifications

The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Whirlpool Washer Agitator Cap Barrier with Seal

Replacing your Whirlpool Washer Agitator Cap Barrier with Seal
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Leaking | Does not dispense fabric softener or detergent | Marks left on clothes
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, KitchenAid, Maytag, Kenmore.
Part# WPW10074580 replaces these:
AP6014843, 285551, 3347290, 3354733, W10074580
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.7
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.1 / 5.0, 30 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
upper portion of 2-piece agitator didn't spin
Popped the agitator cap with a flathead screwdriver. Removed the dust cap, tearing the o-ring in the process. Removed the bolt that holds the agitator in place, removed the whole agitator. Pulled the top portion of the agitator off, removed the dog housing and all pieces of the broken dog pieces. Replaced them, and put it all back together in reverse order. Pretty straight forward repair. Works great!
Other Parts Used:
Agitator Cam Kit
  • Kevin from Everett, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
40 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper Agitator & cogs wore out
I pulled the cap and took a socket wrench turned the stud agit off and removed the upper agitator. Than I assembled the new agitator with the new clogs put the agaiator back on and tightened the stud agit. Replaced new cap and done! Easy job!! Everything is working like new again. This whirlpool washer is 14 years old and still going strong!
Other Parts Used:
Seal, Inner Cap Agitator Directional Cogs Agitator Bolt O-Ring Agitator Cap Upper Agitator
  • Thomas from Troy, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
16 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ratchet assembly in upper half of agitator would not engage.
Fabric softener dispenser snaps in. Apply sideways pressure to snap out. Reach inside agitator and remove agitator cap barrier seal by pulling on tabs. Using socket with extension remove center bolt and rubber seal. Remove upper agitator assembly. Follow instructions provided in agitator repair kit to replace and re-install ratchet ratchet dogs and carrier. Reassemble in reverse of disassembly. Note: Apply a small amount of liquid dish washing detergent to agitator barrier cap seal to ease in re-installation.
Other Parts Used:
Fabric Softener Dispenser Agitator Repair Kit
  • David from Jonesboro, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
15 of 612 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top half of agitator not working
Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.
Other Parts Used:
Washer Agitator Agitator Bolt
  • David from Mission Viejo, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top portion of agitator wouldn't turn.
First I removed the top cap on the agitator, then I removed the second cap inside the agitator. I moved the agitator with my hands and saw that the "dog ears" were worn and no longer touched the agitator and couldn't move it. I then used a nut driver to remove the nut that held the top portion of the agitator onto the bottom portion. I made a note of the worn parts, got online at PartsSelect.com and ordered the replacement parts. A few days later the parts arrived and I repeated the above process in reverse using the new parts. It now works like new!!! It wasn was very easy. Thanks!!!
Other Parts Used:
Agitator Cap Upper Agitator Agitator Repair Kit
  • Michael from El Segundo, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator did not turn
I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.
Other Parts Used:
Agitator Repair Kit
  • Mark from Whitehall, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper agitator would not move
Begin by removing the fabric softener dispenser then the barrier cap can be pulled from the agitator this will allow access to the agitator retainer bolt use an 11mm socket and extension to remove it once the bolt is out the agitator assembly can be pulled straight up out of the machine. To separate the upper agitator from the lower placing the agitator on the floor and placing your feet on the lower half and pulling up on the upper half will separate the two parts, however before performing this operation the agitator cam assembly may be heat set in place, looking down into the upper agitator there are four lugs that hold the cam in place if you use a sharp knife and cut thru the areas that have been heated and welded together separation of the two half's will be made easier. Once all the old cam parts are out reassemble the new parts the same way as the old ones were removed, the cam kit and the thrust washer kit come with a diagram in case you forget how to reassemble the parts. The agitator assembly simply slips back onto the drive splines, the attachment bolt has a seal under it that can be crushed if the attachment bolt is tightened too tight, I could not find a torque specification for this bolt so what I did was tighten the bolt until it contacted the seal completely and then applied just enough torque to turn the bolt until the agitator began to turn along with the bolt, then just install the barrier cap and seal and replace the fabric softener dispenser and the job is done, if you're washer is like mine I spent more time cleaning parts than actually performing this repair.
Other Parts Used:
Spacer, Thrust Direct Drive Motor Coupling Agitator Cam Kit
  • Nathan from OCEANSIDE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top agitator cam arms worm
Removed the agitator and seperated the top unit notice the cam arm were worn, order the parts on line Sunday After noon and recieved the parts the next week! Great service very easy I did call customer Service checking on delivery spoke Steve who was very helpful.
Other Parts Used:
Washer Upper Agitator Agitator Cam Kit
  • Marvin from Lake City, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washing machine was making a loud noise
I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.
Other Parts Used:
Agitator Cam Kit
  • Duane from South Deerfield, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Found seal had split on agitator cap
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .
Other Parts Used:
  • Kim from Cleveland, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Danny
January 18, 2018
No the washer tub went washing some time get's unbalance and start beating&banging and now some water leak's out
For model number wtw4800XQ2 washer
PartSelect logo
Hi Danny, Thank you for your question. If the tub is shaking and banging, there are some parts that you will need to check to see which one is causing the issue. You will need to check the agitator directional cogs, the suspension rods, the suspension rod supports, the springs, the drive block, the inner seal cap, the rod supports, the agitator, the levelling legs and the clutch assembly. I hope this helps. Thank you and have a great day!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Randy
July 6, 2023
Is there a lint filter on this model washing machine? We are getting marks, I assume lint, on our synthetic clothing. I have looked through the diagrams but haven't been able to find one listed. Thanks
For model number la8800xsw1
PartSelect logo
Hello Randy, thank you for contacting us. According to our research, your model does not have a lint filter. If you have hard water and use powdered detergent, you may notice stains on your dark clothes. That is because powdered detergents do not always dissolve in hard water, which can leave streaks. To avoid this issue, be sure to completely dissolve powdered detergents in washing machine wash water before adding clothes. The best course of action is to switch to a hardworking liquid detergent if you are currently using a powder formula. We hope this sorts out your problem!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Robert
July 22, 2019
What's wrong when the machine is on spin the whole machine move across the floor banging
For model number WTW4800XQ4
PartSelect logo
Hello Robert, Thank you for the question. I suggest checking the Suspension Rod Kit, PartSelect Number PS11703290. The rods keep the tub balanced and from banging around. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11748113
Manufacturer Part Number: WPW10074580
Brand
Model Number
Description
Kenmore
11016922500
Washer
Kenmore
11016922501
Washer
Kenmore
11016922502
Washer
Kenmore
11016922503
Washer
Kenmore
11016922504
Washer
Kenmore
11016942500
Washer
Kenmore
11016942501
Washer
Kenmore
11016942502
Washer
Kenmore
11016942503
Washer
Kenmore
11016962500
Washer
Kenmore
11016962501
Washer
Kenmore
11016962502
Washer
Kenmore
11016962503
Washer
Kenmore
11016964500
Washer
Kenmore
11016964501
Washer
Kenmore
11016964502
Washer
Kenmore
11016964503
Washer
Kenmore
11016972500
Washer
Kenmore
11016982500
Washer
Kenmore
11016984500
Washer
Kenmore
11016986500
Washer
Kenmore
11020052990
Washer
Kenmore
11020052991
Washer
Kenmore
11020056991
Washer
Kenmore
11020072990
Washer
Kenmore
11020092990
Washer
Kenmore
11020096990
Washer
Kenmore
11020097990
Washer
Kenmore
11020112310
Washer - AUTOMATIC WASHER
Kenmore
11020112311
Washer - WASHER
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service