The main drive belt is designed to ride on the pulley until the basket gets up to speed.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Washer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Burning smell | Spins slowly | Spinning Issues
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, Maytag, Kenmore, Amana.
Part# WPW10006384 replaces these:
AP6014712, W10006384, WPW10006384VP
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
4.0
Filter By Rating:
5 Stars
3
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
1
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Brian C - October 3, 2023
Verified Purchase
Drive belt for our washer.
The part worked well, easy to install. However that was not the problem with the washer. We have ordered a new washer.
★★★★★
★★★★★
Ramir R - April 20, 2022
Verified Purchase
Perfect!
Perfect fit replacement!
★★★★★
★★★★★
Sabrina O - December 6, 2021
Verified Purchase
Tight but fit
The belt was a little tight to put on the washer. It took two days and three people to get it on properly. Works fine once on though.
★★★★★
★★★★★
Mike L - October 3, 2021
Verified Purchase
Easy fix
Easy fix but have a second issue. Parts on order.
★★★★★
★★★★★
Nicholas F - February 8, 2019
Verified Purchase
scam
you will never stop ordering parts: this part 25% of the time ,that part 45% of the time,the other part 15% of the time UNTIL YOU REPLACE THE WHOLE MACHINE AND THEN IT WILL NOT BE FIXED
February 11, 2019
Hello Nicholas, Thank you for the review. The percentages are based on what issues the previous customers have had and what they ordered to fix the issue. They are determined by previous customers and what they input at the time they placed their order during the survey. These are just suggestions and not every issue is the same so it can very. We are very sorry for the inconvenience. We do have a Q&A section as well to ask a expert a question. Hope this helps!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 13 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Other Parts Used:
Paul from E NORTHPORT, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set, Wrench (Adjustable)
16 of 22 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Other Parts Used:
Terry from HANCOCK, MD
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
8 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Other Parts Used:
Thomas from GRAIN VALLEY, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tub motor shot
Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!! The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times with NO answer, only automated.
Suspension rods were worn; washer is 10+ years old
Replaced the suspension rods, suspension rod supports, main drive belt, tub centering springs, water supply hoes, and washer drain hose. Taped new front suspension rods to side of tub to ensure that they did not slide down when raising the washer off its back from the floor. Had a helper lift the tub, which made attaching the new suspension rods easy. The tub is extremely heavy so by a helper lifting it up it made attaching the new suspension rods much easier. IMPORTANT: According to the technician's manual, which was taped to the inside of the washer, it is absolutely necessary to recalibrate the washer after replacing any suspension parts. We did this by following the instructions in the tech manual. Failure to recalibrate a washer could result in poor performance. The procedure is different for each brand or model of washer, but again is absolutely essential after replacing suspension parts of any kind. For some unknown reason, our washer did not have the tub centering springs. Our model should have had the springs.Facing the washer, we attached one to the front left tub housing and one to right rear of the tub housing. Recommend that anyone watch the installation videos for the suspension rods, center springs, and main drive belt before attempting the repairs.
Washer won’t go into spin cycle! Tries too but then stops
Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
39 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sue
December 30, 2017
My washer stopped spinning and I smelled a rubber smell. I followed your directions for replacing the drive belt and when I took the cover off I found a lot of black oil on the cover all over the pulley on the right. Is that normal when the drive belt breaks down?
For model number WTW5700XL2
Hello Sue,
Thanks for your question. Replacing the belt is a good start for your issue - we would also advise cleaning the pulleys and seeing if any parts are leaking oil onto it.
I hope this helps.
15 people found this helpful.
Was this helpful?
Thank you for voting!
Bethany
April 22, 2018
I’m having issues with my washer going into a fast spin. It will spin but not enough so my clothes are still dripping when it finishes. If i run a small load and put it on the solo spin cycle it will then spin fast enough. Do i need a new belt?
For model number WTW4800XQ0
Hello Bethany, Thank you for your inquiry. We would actually recommend checking the agitator directional cogs, agitator cam kit and shift actuator first. You can inspect the belt for any wear and tear and if it looks worn, then it should be replaced. Hope this helps!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Donna
January 22, 2018
When the load is slowing down from spinning it sounds like it may be a coin or something underneath the bottom of basket. Can you help?
For model number MVWX700XW2
Hello Donna,
Thanks for your question. Check for any loose objects that may have fallen into the washer. If there is nothing, check the belt and the suspension rods with their supports, as that can cause a noise similar to what you are experiencing.
I hope this helps.
My washer stops when it seems to get warm. It will not spin and i can still hear the motor or sensors running. If i turn it off and wait a few hours, then restart it will run. Will not spin water out
For model number WTW4950XW2
Hello Linda, thank you for inquiring. For this symptom you will want to replace either the Shift Actuator part PS11747977, the Lid Latch Assembly part PS3497627, or this Drive Belt part PS11747978. We hope this helps.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Edward
March 20, 2019
Squeaking sound only during agitation cycle, even on delicate cycle..
For model number wtw4800xq1
Hello Edward, thank you for your question. The squeaking noise could be coming from the agitator, belt, drive block or pulley. We would recommend checking over those parts first to see if you can notice any wear and tear and if so, replace the corresponding part. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Vandara
May 14, 2019
Hi thank you, i want to order washer machine Whirlpool belt. How to i order the belt ?
For model number WFC7500VW3 whirlpool
Hello Vandara, Thank you for the question. You can enter the part number into the website and there will be a add to cart button to proceed with the order. You can pay with Credit card on the site. You can also give us a call at 1-877-910-4611. Thank you for your inquiry, good luck with this repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Joseph
August 2, 2018
Powers up but will not agitate
For model number wtw560xw3
Hi Joseph,
Thank you for your question. If the washer is not agitating, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the washer, the shift actuator, the drive belt, the clutch assembly, the lid latch assembly, the washplate, the hub and the shield. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Tammy
February 28, 2018
My washer is noisy (kind of squeals) when it is spinning. When the machine is not running I have noticed that the empty tub is very loosy goosy to the touch. Any idea if this sounds like it needs the belt replaced? Or?
For model number MVWC200BW0
Hi Tammy, Thank you for the question. I suggest checking the Tub Seal, Part Number: PS3407958 for wear. You can also check the block, Part Number: PS1410833 and make sure the Tub Ring, Part Number: PS11756029 is not damaged or needs to be replaced. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Danita
February 8, 2018
What is the length of this belt
For model number MVWX500XW2
Hi Danita,
Thank you for your question. The belt is approximately 92-1/4 inches long, 1/4 inch wide with 4 ribs and 3 grooves. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Vandara
May 14, 2019
Hi ,do washer machine Whirlpool have belt the same size
Hello Vandara, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch a...
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747978
Manufacturer Part Number: WPW10006384
