Part Location Diagram of WP99002780 Whirlpool Lower Wheel Assembly
See part 8 in the diagram
Replacing your Maytag Dishwasher Lower Wheel Assembly
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Lower Wheel Assembly

★★★★★
★★★★★
4 Reviews
$15.84
  In Stock
PartSelect Number PS11747717
Manufacturer Part Number WP99002780
Manufactured by Whirlpool
Product Description

Lower Wheel Assembly Specifications

This lower dishrack roller is less than two inches in diameter. It is made entirely of plastic.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Maytag Dishwasher Lower Wheel Assembly

Replacing your Maytag Dishwasher Lower Wheel Assembly
Troubleshooting
This part fixes the following symptoms:
Not cleaning dishes properly | Noisy
This part works with the following products:
Dishwasher.
This part works with the following products:
Maytag, Amana, Jenn-Air, Admiral.
Part# WP99002780 replaces these:
AP6014478, 9-3095, 903095, 99002780
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
5.0
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.8 / 5.0, 28 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Broken latch handle
The hardest thing was figuring out that you only need to purchase the latch handle because it only comes as a complete latch assembly, why they even list the latch assembly as a separate part in the parts list stupid. (you get the handle and latch already put together and it cost less than the latch assembly without the handle). Anyway all you need to do is disconect the power from the dishwasher (unless you like to live dangerously like me) take your drill with the correct size torx bit and remove all the screws on the inside door pannel (the top center two screws actually hold the latch assembly in place). Disconect the 4 wires from the old part and reconect them to the new part and reinstall all the torx screws being careful not to strip the plastic threads that they screw into if you are using a drill. Whole process takes less than 5 minutes. I am surprised that Maytag used such a flimsy handle assembly in their dishwashers since they are supposed to have the repair men with the most time on their hands. They probably sell just as many handle assemblies as they do dishwashers that have this particular part in it, probably more since you will probably have to change it 2 or 3 times during the life of the unit.
Other Parts Used:
Dishwasher Door Handle And Latch Assembly with Switch
  • Walter from Tucson, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1082 of 1118 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 broken wheels on basket
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....
Other Parts Used:
  • jeanne from waynesboro, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
371 of 374 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clips to hold the folding tines on the bottom rack were broken; also replaced some wheels on same rack.
It took awhile to figure out how to install the peg clips; I still have my manual, but there is no diagram or picture to show how they are installed (and not on the internet either - not even Amana's site), but I figured it out... so here are the instructions I have created.

On the rear part of the lower rack, you will notice that there is a row of larger spaces between the bars; we are only concerned with the 3 farthest right spaces & the 6 bars that create them.

Install both clips with the ‘flange’ that wraps around the bar inside the square; this will position the clamps that hold the clip in place on the outside edge of the bar.

Place one clip on the far right bottom bar; place another clip on the left hand side of the 3rd space (4th bar from the bar the other clip was attached to on the right).

There are small ‘legs’ that protrude from the folding tines on one end of each; place the tines so that the 2 large tines on both are on the outside, the 4 straight tines are on the inside of the squares when they are folded down, which will put the little ‘legs’ down by the far left square.

Snap the tines into the small clamps on the ends of the clips, so that the loops on the ends will rotate up into the larger clamps when the straight tines are folded down, which will hold them in place.
Other Parts Used:
Adjustable Peg Clip
  • Penny from Perry, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
370 of 377 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wash Quality Was Getting Bad
The upper arm was held in by a torx screw. The shoulder on the screw held the arm in place. Once removed I simply swapped parts and installed screw. The lower arm was held on by a plastic nut with knurled edges that you can remove by hand. The arm simply lifted off and I swapped arms again. The rollers are held on by a curled plastic lock that grips the wire basket.
Other Parts Used:
Silverware Basket - Gray Docking Station with Flappers Lower Spray Arm - Shield Included Upper Rack Wheel Wash Arm Cap Upper Spray Arm
  • CHRISTOPHER from Spalding, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
232 of 444 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel had broken off along with the folding tines' clip
All I had to do was to snap the parts into place. I also had someone come here to find a leak in my dishwasher. It was in the latch and seal that kept the soap dispenser closed. They wanted to charge me over $50 when the part only cost less than $9 with shipping. I just ordered it and installed it myself. Piece of cake!
Other Parts Used:
Folding Tines Sleeve Adjustable Peg Clip
  • Gina from West Alexandria, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
130 of 254 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher lower basket suffered from wear and tear
Slipped into place the two wheels on lower basket that had gone missing; removed brackets for adjustable section that were broken and easily snapped knew ones into place; connected handle to flatware basket and replaced the old one. Why we didn't do this years ago!
Other Parts Used:
Silverware Basket - Gray Adjustable Peg Clip Siverware Basket Handle
  • Liz from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
130 of 255 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Didn't spray water.
Inside the Dishwasher on the bottom of unit, I removed the dish cart. The removed the sprayer arm with an adjustable wrench on the plastic nut on the center top. Then removed the top three screws with a Torx 20 screw driver and removed the plastic cover, then removed the single screw above the black plastic water pump piece and took it off. Then removed the six additional screws that were then displated after the previous cover was exposed. Finally I unscrewed the ivory colored plastic shaft which holds the food processor blade from the metal motor shaft with a adjustable wrench. Upon inspecting the ivory plastic shaft I noticed that the threads were stripped inside it. Which means it didn't turn when the motor would turn and wouldn't drive the water pump.

I ordered the replacements and noticed that the replacement for the plastic ivory colored shaft was a metal shaft. It had new pieces as the food processor blade had notiches in new places. The kid had all the replacement parts and a good set of instructions for what to replace and where it would go.

Then I assembled the washer as I had taken it apart. And it worked perfectly the first time. It has been repaired and working for a few weeks now without incident.
Other Parts Used:
Seal and Chopper Kit Fold Away Tine Pivot
  • Joseph from Merrill, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
127 of 205 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Wheels
Snapped on new wheels
Other Parts Used:
  • Mary J. from Westwood, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
67 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic wheel fell off and melted
Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.
Other Parts Used:
  • David from sleepy hollow, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
67 of 129 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new range handle
was a 15 minute job
Other Parts Used:
Rack Adjuster with Wheels- Right Side Door Handle
  • audrey from roscoe, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

5 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Adam
November 19, 2018
How many wheels are there in the model?
For model number mdb7100awq
PartSelect logo
Hello Adam, Thank you for the question. As Per Whirlpool, this substituted part only has 6 wheels instead of 8. If you have the Original rack, you will need 8 wheels. Thank you for your inquiry, good luck with this repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Adam
November 19, 2018
The rack part in which the wheel pushed into is rusted and broken.Is there a new replacement "wheel assembly" will fit in the existing rack(lower)?
For model number MDB7100AWQ
PartSelect logo
Hello Adam, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS11746834, but if the rack is rusted and broken it will need to be replaced. Part Number: PS1960964. Thank you for your inquiry, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
AJ
June 24, 2021
Does this come with both set of wheels for the bottom rack? front and back?
For model number MDB8750AWS
PartSelect logo
Hello AJ, Thank you for the question. This is one individual Wheel Assembly. We hope this helps, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Joseph
November 22, 2022
Does the lower rack wheel need to be purchased in pairs
For model number MDB8951BWS
PartSelect logo
Hello Joseph, thank you for your question. It does not need to be but it is recommended. These rollers tend to wear down at the same speed, so it is recommended to replace both pairs at the same time. Thank you and have a great day

1 person found this helpful.

Was this helpful?
Thank you for voting!
Garnell
February 11, 2018
Left door spring attachment with 16 inch broken cable. How do I install them. You don't show the cable on the diagram. Is it available?
For model number JDB6510AWP
PartSelect logo
Hi Garnell, Thank you for the question. The Door spring is PartSelect Number PS11746856 and the cable is PartSelect Number PS11747654. Please see the video link below for the spring. We do not have a video for the cable but here are some steps. Attach cable to the hinge. Then attach cable to cable link. Route under the roller. Attach to the short hook of the spring. Place large hook of spring into spring adjustment. Hope this helps! https://www.youtube.com/watch?v=YPF4ckYRZRc

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747717
Manufacturer Part Number: WP99002780
Brand
Model Number
Description
Maytag
3-RACK
Dishwasher - Maytag Dishwasher 3-Rack
Amana
ADB1200AWB
Dishwasher - Tall Tub
Amana
ADB1200AWQ
Dishwasher - Tall Tub
Amana
ADB1200AWS
Dishwasher - Tall Tub
Amana
ADB1200AWW
Dishwasher - Tall Tub
Amana
ADB1500AWB
Dishwasher
Amana
ADB1500AWB0
Dishwasher - DISHWASHER
Amana
ADB1500AWB10
Dishwasher
Amana
ADB1500AWB37
Dishwasher
Amana
ADB1500AWB41
Dishwasher - DISHWASHER
Amana
ADB1500AWB46
Dishwasher - DISHWASHER
Amana
ADB1500AWQ
Dishwasher
Amana
ADB1500AWQ0
Dishwasher - DISHWASHER
Amana
ADB1500AWQ10
Dishwasher
Amana
ADB1500AWQ37
Dishwasher
Amana
ADB1500AWQ41
Dishwasher - DISHWASHER
Amana
ADB1500AWQ46
Dishwasher - DISHWASHER
Amana
ADB1500AWS
Dishwasher
Amana
ADB1500AWS0
Dishwasher - DISHWASHER
Amana
ADB1500AWS10
Dishwasher
Amana
ADB1500AWS37
Dishwasher
Amana
ADB1500AWS41
Dishwasher - DISHWASHER
Amana
ADB1500AWS46
Dishwasher - DISHWASHER
Amana
ADB1500AWW
Dishwasher
Amana
ADB1500AWW0
Dishwasher - DISHWASHER
Amana
ADB1500AWW10
Dishwasher
Amana
ADB1500AWW37
Dishwasher
Amana
ADB1500AWW41
Dishwasher - DISHWASHER
Amana
ADB1500AWW46
Dishwasher - DISHWASHER
Amana
ADB1500AWZ
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service