Washer Transmission Stem Seal
$14.11
In Stock
PartSelect Number
PS11746747
Manufacturer Part Number
WP8577376
Manufactured by
Whirlpool
Product Description
Washer Transmission Stem Seal Specifications
Sold individually.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Kenmore, Whirlpool, KitchenAid, Roper.
Part# WP8577376 replaces these:
AP6013521, 356934, 356934BULK, 356934D, 8577376, 91938, 99404, LP630, WP91938
Customer Repair Stories
Average Repair Rating: 2.0 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The motor turned with loud noise ,but nothing else worked
I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again.
Other Parts Used:
-
Bob from East Palestine, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
83 of 176 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was leaking underneath machine
While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.
Other Parts Used:
-
RAY from DEER PARK, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No parts
A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Other Parts Used:
-
Jason from WENTZVILLE, MO
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive shaft leaking
Washer was leaking -- in part from hoses that had loosened over time due to unbalanced loads and age, and partly from a worn pump -- and not agitating/spinning properly. Fixed hoses, replaced pump and clutch. Unfortunately, when I pulled apart direct drive to replace clutch, the drive shaft started leaking because old seals worn and compromised on disassembly. Have to give credit where due -- YouTube invaluable here -- pulled and disassembled drive shaft, removed old seals, replaced and reassembled. Time consuming, but if you keep track of where things go, not too bad. 3 things I wish I knew in advance: (1) for an old washer you definitely need a spanner nut wrench (like 15-25 bucks online) to remove the spanner nut so you can pull the basket and get to the seals -- no wrench/pliers/vise substitute will do the trick; (2) the shaft seals have metal washers inside the rubber/plastic -- when you're removing the old seals, you might need to chisel (hammer and small flat head screwdriver) the old seals out instead of just pulling out the corroded rubber which will leave the old metal behind; (3) if your time is valuable, try to diagnose all the likely sources of your problem and buy the parts to repair at once rather than doing piecemeal like me. Took me 2 weeks and two complete tear downs to finish a repair that should have taken me an afternoon. I love my local Appliance Parts guy -- he's knowledgeable and usu. has what I need or can get it fast and I like supporting local brick and mortar -- but if time is important to you, taking advantage of online companies that allow you to return what you don't use may save you time.
Other Parts Used:
-
Al from OCEAN, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
January 30, 2018
I want to replace some of the seals and bearings on center support and brake tube, # 3362087 a blog site said the bearing and top and bottom seals needed a special tool to install , do you have a utube video to provide intructions, and where or what is the speical tool?The upper and lower post bearing kit, is 285203
For model number 11092389200
Hello Tom, thank you for your question. Part number WP8577376 shouldn't require any special tools to install. Here is a video that should help you with your repair. https://www.youtube.com/watch?v=9DmBGhXD5-Q. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11746747
Manufacturer Part Number: WP8577376
Manufacturer Part Number: WP8577376
Brand
Model Number
Description
Kenmore
10682872600
Washer
- Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
1101050299
Washer
- Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts