This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is found between the motor pulley and the drive pulley, and it connects the motor to the drive system. When the belt is running, it allows the basket or tub to spin. If the belt is stretched, worn, or broken, the tub will not turn. A warped belt can also cause the washer to be noisy while operating. This part is an authentic OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Washer Washer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Spins slowly | Burning smell | Spinning Issues
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Kenmore, Inglis, Amana.
Part# WP8540101 replaces these:
AP6013037, 8540101, 8540348
Customer Reviews
Average Rating:
★★★★★
★★★★★
23 Reviews
4.9
Filter By Rating:
5 Stars
21
4 Stars
1
3 Stars
1
2 Stars
0
1 Star
0
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Christine N - July 24, 2018
Verified Purchase
Easy repair
Great price, easy to install, quick delivery.
★★★★★
★★★★★
Sanjiwan S - September 10, 2021
Verified Purchase
Easy repair-super fast service
The part was in excellent condition, arrived so fast after placing the order that I was amazed. Thanks for great service.
★★★★★
★★★★★
John B - November 8, 2019
Verified Purchase
Fast
New belt was noticeably shorter than the worn original, it was stretched that badly. I soaked the new belt in hot water to soften it up making installation easier. Washer works like new
★★★★★
★★★★★
Wolfe S - April 23, 2019
Verified Purchase
Regular belt, easy to install
Part came fast. Good service
★★★★★
★★★★★
Leslie M - April 10, 2021
Verified Purchase
repaired
Part was as described.
★★★★★
★★★★★
Mark Y - April 7, 2021
Verified Purchase
Easy repair
A little expensive, but arrived less than 24 hours after ordering, and was an OEM part. Washer is 10 years old, old belt was at least 2” longer from stretching.
★★★★★
★★★★★
Samuel E - June 5, 2021
Verified Purchase
Great part
The part is great, I got on time, Thank you so much.
★★★★★
★★★★★
Abderrahim K - October 13, 2021
Verified Purchase
thank you
i'm so happy with that product!
★★★★★
★★★★★
Catherine C - October 2, 2019
Verified Purchase
Easy repair, very pleased
Fast delivery ,well packaged to protect part during shipping, would definitely order from your business again.
★★★★★
★★★★★
Debra Lynn B - May 1, 2020
Verified Purchase
Exact Fit
Washer had broke. Son opened up machine and found the Drive Belt shredded. He offered to repair it for me. Called local appliance repair services. Drive belts were going to cost more than what I would pay buying it from Part Select, not to mention what the costs of service if I would require that as well. I ordered the part from Part Select, received within 2 days. My son was able to install and repair within minutes! Thank you for providing a service of obtaining parts and omitting the middle man, whom in this case was not required with inflated costs.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 5 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bad drum belt
Our whirlpool washer drum wasn't turning and there was a thunking noise from the machine when the drum should have been rotating.
I opened the top and back of the washer using a ratchet wrench. There were 4 screws holding on the top (at the top rear of the machine) and about 12 or more holding on the back panel. Removing these I could see the belt had become frayed, had come off of the drum, and was bunched around the motor drive wheel. The old belt was still usable, but clearly not going to last much longer so I purchased a new belt. The new belt was tighter than the old belt (which is good) and so took a fair amount of effort to get back onto the drum. I had to hold in place while turning the drum, something hard to do because of the braces on the back of the washer get in your way. But, I eventually got the belt propery seated. I then replaced the back and top panels. All appears to be working as it should.
Other Parts Used:
Keith from Austin, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
82 of 105 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer belt stretched from years of use and walked off pulleys
I pulled the washer away from the wall to comfortably access the back panel. I then removed about a dozen 1/4 drive screws. I had to remove all the screws in the panel and the screws and cross brace directly behind the drum in order to install the new belt. Note: it will seem like the belt is too small when in reality it is perfect. There is no type of adjustments or tensioners that I found so you need to place the belt on the motor pulley correctly and then walk the belt on the drum pulley. Make sure the belt is lined up with the marks on the drum pulley that the original belt had left. You may need to attempt to walk the belt on 2 or 3 times before it finally goes on. If you have any mechanical knowledge you will find this to be a gravy job.
Other Parts Used:
Michael from PHOENIXVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
10 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor bear bearings failed, making a very load screechy sound.
Turned off water unplugged washer removed screws a lot of them. Removed lower back brace. removed belt. 1 bolt holding motor on removed. disconnected ground wires and motor plug. wiggled motor out wiggled new one in put belt on and the many screws on the back on turned water back on, plug in and it work like a washer .
It didn't seem like the drum was spinning fast enough when washing a full load to wring all the water out of the clothes
I basically just followed the directions in the Parts Select video. The only thing that was a little difficult was getting the new belt to feed onto the drum pulley, but after a couple of tries I was able to get it on. I'm glad the video mentioned this might be a little difficult or I might have thought I was doing something wrong.
Other Parts Used:
David from Agawam, MA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive belt replacement
I never did the repair because Partselect.com shipped the wrong part. Then they charged me a 2nd time to resend the correct part plus the fees for shipping the correct part overnight which I did not get it until 2 days later. Now I shipped both parts back & have to wait for a refund. I will never order from them again!
Other Parts Used:
Timothy from PAINESVILLE, OH
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Liseanne
August 1, 2019
My washer works fine until it is on the spin cycle. It is very loud when it is spinning, but only on the spin cycle. Is there a bearing on the tub that could be making the noise?
For model number IFW7300WW01
Hi Liseanne,
Thank you for your question. The bearings are part of the outer tub. If the issue is the bearings, the outer tub, part number W11239040 , has been discontinued by Whirlpool and you will need to contact them for information on a replacement part. Their telephone number is 1-866-698-2538. If they provide you with a part number for the replacement part, you may call us back with it and we can verify if we have it available for you. You may also be able to locate the part you need by trying the following:
Using a search engine to type your part number and see if other retailers still have this part in stock.
Visiting online stores such as eBay and finding sellers that have this part.
Trying retailers and repair stores in your local area to see if they have the part in their inventory.
Talking to a local repair technician, who may have the part you need, or may be able to repair your existing part. If it is not the bearings causing this issue, you should check the drain pump, the drive belt, the shock absorbers, the tub baffle and the counter weight. I hope this helps. Thank you and have a great day!
11 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing help...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
