This dishwasher door spring is sold individually. It is recommended if you are replacing one side, to replace both.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your KitchenAid Dishwasher Door Balance Spring
Troubleshooting
This part fixes the following symptoms:
Door latch failure | Door won’t close | Noisy
This part works with the following products:
Dishwasher.
This part works with the following products:
KitchenAid, Kenmore, Jenn-Air, Whirlpool.
Part# WP8270182 replaces these:
AP6012324, 8270182
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
4.8
Filter By Rating:
5 Stars
5
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ardith L - April 23, 2019
Verified Purchase
Strong spring, takes a bit of strength to open it.
A fairly easy repair.
★★★★★
★★★★★
Brett M - September 11, 2018
Verified Purchase
worked
it worked
★★★★★
★★★★★
James I - September 5, 2018
Verified Purchase
Excellent service
The part was exactly what was described and 2hat I needed to fix the door on my dish washer. Excellent service and prompt delivery. Thank you
★★★★★
★★★★★
Sean J M - August 29, 2018
Verified Purchase
Perfect, just what I was looking for
Spoke to my friends about the experience dealing with Part Select. Service could not have been better, and then the How to Install video took it over the top! Wow customer service!!
★★★★★
★★★★★
Jean-Maxime C - August 22, 2018
Verified Purchase
Excellent quality
Fast shipping, perfect quality. Thanks!
★★★★★
★★★★★
Rosanne W - August 10, 2018
Verified Purchase
proper parts suggested to purchase in addition to the spring.
I thought it was the spring that had broken, because we experienced the broken spring in the past. When looking up the parts, "PartSelect" suggested to purchase guide cable as well. When I took the door apart, I found that the springs were fine, but the guide cable was broken. Thanks
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 10 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
latch pops open on door during cycle...
Replaced strike plate...but may not have needed it ...He used a screw under the front of the strike plate as a wedge to increase tension...He said this has happened to this model before and an old tech told him about this fix... It must be a defect in the model that after a while the strike plate needs more tension..sent unopened ,unused parts back
Ordered the parts on your site since I could find a parts schematic that really helped. I had to move the unit out and replace the spring on one side. We replaced both nylon cords since the other was showing a little wear. Received the parts quickly and made the repair the same day.
Disconnected dishwasher from countertop and slid out about 1.5 feet. Removed old link. Installed new link and reconnected to spring. slid dishwasher back under counter. Replaced 2 screws back to countertop. It was really really easy.
Turned off water supply and electricity, removed the front kick panel on the dishwasher. Disconnected the water supply line, removed the two screws above the door securing the dishwasher to the underside of the countertop. Pulled the dishwasher out from under the counter, replaced the spring and balance link for each side. I found that the new balance link kit that I purchased was better engineered that the origanal equipment.
First, ordering parts and getting diagrams from parts select is so efficient and make tthe installation so manageable. Using installation tips off the site gives u confidence to do it. My issue was that I could not get the dishwasher from under the counter. I removed the kick plate and screws holding it to the counter, but it was not coming out all the way. So I had to use a coat hanger to hook the spring. I attached the nylon cord first. Then I pulled the spring taut with the hanger and it was easy to thread the cord around the pulley system. I actually attached it to the door before tensioning the spring to make it easier. Door works great now.
Other Parts Used:
Peter from Westfield, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
12 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken link to door assembly
Actually, the repair was very simple because of the you tube video demonstrating the repair. This made the repair very easy. I repair/replaced both springs and links
One day when opening the door there was a "Snap" and the door fell open.
I first went on line to the KitchenAid repair web site and found my problem listed and instructions given . This first of all led me to a parts drawing for my model and then to the site connection to order the parts and receive the instructions. The parts arrived quickly and the instructions were thorough and easy to follow. This was a good experience for me.
One Spring and both Balance Link Kits were broken. The repair itself was incredible easy, especially after watching the repair videos. Maybe 2 minutes per side. The moderately difficult part was removing the water supply and drain lines. Our dishwasher is some distance away from the kitchen sink. The supply and drain lines are routed behind and through some lower cabinets making reconnection a bear. Finally used a wire coat hanger as a guide and was able to re-thread the lines through the cabinets. The dishwasher could not be removed from its cabinet without first removing these lines.
Dishwasher door "flopped down", detergent dispenser did not open, built in unit fastening screws replaced.
So after 4 yrs wifey not happy which makes me not happy. Biggest issue was figuring out how to pull built in dishwasher out. Not really that tough. Pull base plate, disconnect water supply, pull drain line then pull unit out. Ordered parts (two new springs, set of link kit, new dispenser). Once out just followed the PERFECT instructions sent to me with my order from PartsSelect. Took a couple hrs but I was in no hurry. Probably saved myself over $500!
with dishwasher door open, connect the spring to the back frame upright hole. attach end of cord with eye opening onto the spring. Using the box end of a wrench, slip it over the open end of the spring and pull the spring toward the front of the dishwasher. That will give the cord enough slack to thread it around the pulleys and onto the door mounting bracket.
Other Parts Used:
Rich from Tracy, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
1 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
August 8, 2017
Door flies open when opened. Which springs do i need to purchase??
For model number KUDP01FLSS3
Hi John,
Thank you for your inquiry. The door spring you will need to fix your dishwasher door is part number WP8270182. You will need to purchase 2 of them as it is recommended to replace both at the same time. I hope this helps with your repair. Thank you and have a great day!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Lynette Parker
April 30, 2018
My dishwasher door opens and then falls open very hard and the door is heavy now.
For model number KUDSO1FLSS1
Hello Lynette, thank you for your question. If the door is falling open very hard, almost slamming down, you will want to replace the Door Balance Link Kit Part Number 8194001. There is an installation video on our site which will show you how to install these parts. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sheila
March 29, 2019
Just opened the door to my dishwasher and heard a little noise and now door goes all the way down when i open it. Is this the spring or something else.....
thanks
For model number KUDP02SRSS2
Hello Sheila, Thank you for the question. Sounds like the Door Balance Link may have broke. They are sold as a kit, PartSelect Number PS972325. Thank you for your inquiry, good luck with this repair!
Door spring is broken. What is the correct part # to order or all is the same for Kenmore elite dish washer?
Hello Binh, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
Was this helpful?
Thank you for voting!
David
July 31, 2023
Door flies open like it has a door spring broken, what spring do I need?
For model number MDB8959SKZ0
Hello David, thank you for the query. According to our research, the door spring does not come separately. You may need to replace the left side door hinge, part number PS16660571, and right side door hinge, part number PS16660570. We hope this helps!
Hello Nancy, Thank you for contacting us. I suggest checking the following parts: PS972325 Door Balance Link Kit and PS11745531 Door Balance Spring. One of these two parts are most likely causing the issue. Good luck with your repair!
Was this helpful?
Thank you for voting!
David Alger
December 14, 2017
I am installing the two new springs on my kitchen aid dishwasher kudpo1flbl3. The part number is ps117 45531. My question is i have to remove the dishwasher and disconnect the power and water supply. Is there a video or some sort of instruction that will help me do this?
Hi David,
Thank you for your question. There is a video listed with the part on our website that you may reference. If you scroll down the page, the video is under the photo and information of the part. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11745531
Manufacturer Part Number: WP8270182