Average Repair Rating: 3.3 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven would not shut down, kept heating
The front oven control panel was already in need of replacement. The digital readout had quit working sometime ago, so we began by replacing the control panel as well as the temperature probe. Neither of these items did the trick. Next I replaced the HI/Lo sensor switch. This replacement was a bit more labor intensive. Have to remove several screws and remove a large portion of the top of the stove. Once access is gained to the hi/lo switch, it takes (2) minutes to replace it. This of course did not take care of the problem either. Finally I replaced the bake/broil/convection circuit board. This was a bit of a job, only because of the amount of wires to and from this board. I litterally took a picture of the board (from this web site) and drew in the wires and marked them by color and noted where they went. I then merely unplugged each wire and with one screw, removed the board and installed the new one. After plugging in the wires as per my picture, SUCCESS. The board did the trick. Over all, it was not bad doing the work myself. I know we saved a lot of money my doing it ourselves. Just gotta have patience.
oven wouldn't heat and showed a error message of function not available
pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.
Other Parts Used:
Eugene from Pampa, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven stopped heating
I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.
Other Parts Used:
Christopher from Royal Oak, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chris
November 22, 2021
Oven broiler not working. Element seems ok. No damage. Do I need new thermostat.
For model number S160
Hello Chris, Thank you for the question. if it is just the Broil Element now working and Bake in good, the thermostat will be fine. The Broil Element can short out or become faulty without showing physical damage. We suggest testing the element with a Multimeter. The element's resistance may be in the area of 20 to 40 ohms depending on its wattage. We hope this helps!
The baking element (bottom) "blew out" including a flame up & then the control panel screen went out on our Jenn-air range. The parts specialist that customer service transferred me to recommended checking the high limit switch (thermostat) first: if ok, "probably the electronic control board blown, if not working, try replacing it first". He couldn't tell me where it's located, however (?). It looks like the electronic board is no longer available anywhere to order. Any suggestions? thanks so much!
For model number JES9860AAW
Hello Nancy, thank you for writing. You are correct that the electronic control board is discontinued. Sadly, we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. Good luck with your repair.
Was this helpful?
Thank you for voting!
Shawn
November 16, 2021
Where on the unit the high limit thermostat located? p/n PS11744498
For model number JJW9527DDB
Hello Shawn, Thank you for the question. The Thermostat for this model is located on the back interior panel. You will need to pull out the appliance and remove the back panel to access the Thermostat. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
