Oven Sensor

Hello Tom, thank you for your question! Most often when the oven is not preheating properly, it indicates a bad oven sensor or element. If you are experiencing this problem with both the bake and broil functions, it is likely the sensor. If it is just for one of the functions, we would recommend checking the appropriate element before replacing the sensor. We hope this helps!

Hi Andrew, Thank you for your question. The F3 E3 error code is letting you know that there may be a problem with the oven temperature sensor or the wiring connected to it. Here are some steps to try to see if you can resolve the issue. Power the unit down by turning off the circuit breaker or breakers for one minute. Power the unit up by turning on the circuit breaker(s). Monitor the oven for one minute to ensure the error code does not display again. Verify oven operation. If the error code returns, you will need to check the oven sensor to see if it is working correctly. You will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps. Thank you and have a great day!

Hello David, thank you for your question. Error code 1d11 indicates that there is a runaway temperature while the door in unlocked, meaning that the temperature sensor is getting a reading of over 600 degrees. If you are getting this error while the oven is cool that indicates your temperature sensor might be faulty, or the connection is loose. If the connection is fine the sensor's resistance can be tested with a multi-meter. At room temperature it should read 1070 ohms. If the sensor is fine there might be an issue with the control board, you can try a reset by unplugging or shutting off the breaker to the appliance and then restoring power. If that does not help the control board may need to be replaced. I hope this helps, best of luck with your repair!

Hi Scott, Thank you for your question. The the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check with a multimeter. An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and maintains the internal oven temperature by cycling heat on and off. Before repairs or testing can begin you must disconnect the electricity at the fuse panel, at the circuit breaker panel, or by pulling the plug. Make sure the power is off before proceeding. A jolt from 220 volts can be fatal, use caution! Access the oven thermostat, which is located in different places depending on the make and model: On freestanding ranges, access the thermostat by removing the screws that hold the back panel in place at both ends. On models with front-loading controls, remove the panel and tilt it for access. Be careful not to let the wires disconnect from their components. Some built-in models have a removable backsplash. Lift the backsplash, rest it on the cook top and remove the screws from the backsplash, which holds the rear panel. On wall ovens or eye-level ranges, access the control panel by opening the door and removing the screws that secure it. The screws may be under the exhaust hood or below the control panel. If the control panel is hinged, simply tilt it towards you. On some models both the rear and front control panels must be removed. The screws may be found on the trim and occasionally the trim must be removed. When testing the thermostat switch contacts for continuity, refer to the wiring diagram and remove only those wires being tested - and only one pair at a time. Test switch contact terminals as per your wiring diagram. If the switch lacks continuity at any of the contact terminal points then the entire thermostat switch needs to be replaced. Adjusting the thermostat: Test the oven temperature by placing the tester in the oven's center and leaving it for 30 minutes at 350 degrees. Record the minimum and maximum temperatures of three cycles, then add those figures together, divide the result by six and you have the oven's average temperature. If the average temperature is more than 25 degrees off, try calibrating the thermostat by following your appliance manual instructions for thermostat calibration. Normally, thermostats are calibrated by pulling the oven's thermostat knob off, turning the knob over and adjusting the calibration ring on the back. If your oven doesn't have a calibration ring you may need to replace the thermostat. To remove the thermostat: Disconnect the capillary tube and push it through the back oven wall, being careful not to break the flammable capillary tube wire. Remove the screws that secure the thermostat to the control panel and gently pull the thermostat out, leaving the wires in place. To install a new thermostat, reverse the disassembly procedures (Step 7 above), transferring the wires individually from the old unit to the new. I hope this helps. Thank you and have a great day!

Hi Kelley, Thank you for your question. The F1-E0 error code is a communication error. Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). I hope this helps. Thank you and have a great day!

Hello Damien, thank you for your question. That would be an issue with the sensor, or the electronic board. The sensor's resistance can be tested with a multi-meter. At room temperature it should read 1070 ohms. If the sensor is fine there might be an issue with the control board, you can try a reset by unplugging or shutting off the breaker to the appliance and then restoring power. If that does not help the control board may need to be replaced. I hope this helps, best of luck with your repair!

Hi Mark, Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multi-meter. When testing the sensor with a multi-meter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. If the sensor checks out fine, you will need to check the electronic control board, the oven elements and the wiring between them to determine which part is causing the issue. I hope this helps. Thank you and have a great day!

Hello Arthur, thank you for reaching out. You may need to remove the back panel of the range to access the oven sensor. We have attached a relevant video that may not be of the same model but will help you in accessing the sensor. We hope this helps!

Hi Sue, thank you for getting in touch. Based on the description that you have provided, we would recommend checking the temperature sensor, part number PS11744233, as it is most likely faulty and may need to be replaced. We hope this sorts out your problem!

Hi Thomas, Thank you for your question. If the oven is not heating correctly, the issue may be with the oven sensor. The oven temperature sensor is the part that monitors the oven temperature and signals the electronic control board to turn the elements on and off. Before removing this part from the oven and testing it with a multimeter for continuity, unplug the oven from the electrical outlet. To test the sensor, you will need to reference your owner’s manual to determine what the correct reading should be for your model, as this varies from model to model. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. If the sensor is fine, you will need to check the elements, the electronic control boards and the wiring between the parts to see which one is causing the issue. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!