Door Hinge WP74008014

Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.

Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.

Parts arrived as scheduled with no problems. First I removed and repaced the 2 oven door hinges to see if this would fix the problem with the door not closing all the way (had to push door to get the oven light to go out). Since no instructions were shipped with the new hinges, I followed the information given by other customers on how they were able to change the hinges. Changing the hinges DID NOT fix the problem with the door! The new hinges did not pull the door any tighter than the old hinges. Door closure problem finally fixed by supergluing several round mangnets (Lowes) to the door which pulls the door tight when closed. I learned this trick from another customer's report (thanks for the idea!). Next I removed and replaced the failed control panel. This was the second panel to fail on this oven in the 5 years it has been installed! The first panel was replaced under warranty after approx 2 years of use. Hopefully, the magnets will keep the oven door closed and prevent overheating of the control panel which will allow this poorly designed oven to last a little longer this time!

Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.

We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl

I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.