2-Speed Drive Motor - 60Hz 120V

Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.

First unplug the electrical chord and disconnect the water supply after you have turned it off. Drain all water you can by putting the drain hose into a bucket or water container lower then the drain hose. Remove the two screws at base of the front panel. Then go to the back side of the machine remove the two screws at the top of the back panel, this allow you to remove the top switch panel. Remove the two screws at the bottom outside corners of the back panel and then you can lift the panel up and away from the base. I leaned the back against my dryer because I did not have a helper. Go to the front of the machine, lift the lid and grasp with one hand the machine's sheet metal lift and pull it off the base. There are two metal clips attaching the pump to the motor. The pump slides off and I did not have to remove the hoses. Unclip the electrical connectors from the motor and capacitor. The motor is mounted with two clips with a screw secure it in place. Unscrew and unclip and the motor should slide out. Be sure to inspect the direct drive coupler, the parts not too expensive. I had replaced mine just 4 months ago so I was good to go. Reverse the procedure and you should be in business.

The repair itself was very simply, probably largely due to the design of the machine which made getting to, and replacing the two faulty parts a cinch. Just unscrew the two screws on the motor brackets which hold the motor down, and remove the brackets. Then remove the two smaller brackets which hold the pump to the motor. Then remove the two clamps and hoses from the pump. Lastly disconnect the power supply from the motor and the pump and motor will then come out as one unit. Simply reverse the process when reinstalling the new pump and motor. I used a bit of oil to lubricate the new motor shaft but I am sure it probably isn't necessary. The job should take no more than half an hour tops.

Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft on the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil

1. Watch a video on installation, there are many on the internet.
(unplug the washer)
2. remove the screws on the back of the control panel to lift the control panel out of the way.
3. use a flat head screwdriver to remove the clips that hold the cabinet to the back panel.
4. disconnect the lid switch from the control panel by removing the clip that connects them at the top of the cabinet.
5. tilt the cabinet forward to remove it.
6. use a flat head screw driver to remove the two clips that hold the water pump to the motor and swing the water pump out of the way.
7. use a nut driver to remove the shipping screw that holds the clips on to the motor.
8. disconnect the wiring harness from the motor
9. remove the two clips from the motor with a flat head screwdriver and remove the motor
remove the three prong coupler and rubber gasket from the old motor and put them on the shaft of the new motor
10. remove the 4 rubber pads from the old motor and slide them onto the new motor.
11. insert the new motor into the washer aligning the prongs of the coupler.
12 reassemble the washer in reverse order of disassembly
(the shipping screw does not need to be reinserted into the spring clip that holds the motor)

Followed the video instructions. Had no problems. The video was accurate.

Repair went well and relatively easy, but did not fix the problem.
Suspect timer switch was the culprit. Nothing was clogged or plugged
up. Water pump and impeller were free and clear with no damage
or leaks.