Maytag/Maytag_Thumb/37313.gif
See part 18 in the diagram
Replacing your Maytag Washer Drain Pump play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Drain Pump

★★★★★
★★★★★
5 Reviews
$116.35   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11743017
Manufacturer Part Number WP6-2022030
Manufactured by Whirlpool
Product Description

Drain Pump Specifications

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will not drain | Leaking | Noisy | Pumps but will not spin
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, International, Jenn-Air.
Part# WP6-2022030 replaces these:
AP6009844, 200724, 202203, 202204, 202532, 202540, 6-2022030
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

12 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gerry
October 14, 2017
The pump pulley came off the washer. Is this a factory mounted pulley attached to the pump permanently or is it attached by a bolt? Can i just bolt it back on or would i have to replace the entire pump assembly? Thank you.
For model number Maytag lse7806acq
Hello Gerry, thank you for contacting us. You would need to replace the whole pump as that pulley is not sold separately or removable. Hope this helps!

10 people found this helpful.

Was this helpful?
Thank you for voting!
Richard
April 27, 2018
When the belt is disconnected will the water pump turn freely or with some resistance?
For model number A712
Hi Richard, Thank you for the question. The pump should turn freely with a bit of resistance but should still be fairly easy to turn. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Milton Ahner
August 29, 2017
Does the pump in this model wash machine control the water staying in the tub as its filling? Is there any chance that the drain could siphon the water out of the tub as its filling, or is there a check valve to hold water in the tub?
For model number A512S serial no. 171539
Hi Milton, Thank you for the question. I would start by making sure you do not have a siphoning issue. First check to make sure the drain house is not pushed into the home drain. Then check to make sure the home drain is not plugged or blocked. Some people stuff a rag or paper towel around the gap between the hose and the drain hole thinking it will make the hose fit into the home drain more secure. There needs to be air flow between the drain hose and the outside diameter of the drain hole. It is also a good idea to check the Siphon Break Kit and the Siphon Break Elbow Kit with Clamp. Make sure they are not cracked or damaged or nothing could be blocking them. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Ross
February 25, 2019
Q#1 how old is my machine? It's actually my moms and i'm trying to help her either fix or replace her machine.Q#2 it was overloaded with a big comforter and just stopped doing anything after emitting a burning belt smell, i want to diagnose the problem but the tub is really full of water. how do i get the water out, so i can figure out what's wrong without spilling water everywhere? thank you for your support ;-)
For model number LAT7304AAE
Hello Ross, Thank you for contacting us. Please submit a follow up including the serial number of the unit so we can determine the age. If unplugging the unit and plugging it back in after 1-2 minutes does not force the water to drain, try to move the timers into the spin cycle so it can drain. If that fails then you would have to manually empty the water. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Ross
February 26, 2019
This is a followup question. How old is my Maytag washer? Serial # is a0132943ks
For model number LAT7304AAE Maytag washer
Hello Ross, Thank you for the question. According to the serial number this product may have been manufactured August of 1994. I hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Linda
May 10, 2019
Hi, i have a problem i hope you can help me with. My washer will not complete a cycle. It agitates fine. But when it starts into the spin cycle, it starts then promptly stops. I don't have a meter. Please help!
For model number LAT8240AAW
Hi Linda, thank you for your question. When you appliance will not advance there are a few parts that you should check. You should take a look at your lid switches and your timer itself. I hope that helps. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Joe
December 12, 2017
My machine leaks a small amount of oil. Do i need to worry about it running out of oil
For model number A107A
Hi Joe, Thank you for your question. Yes, eventually you would run out of oil in your machine. How fast that occurs depends on how much oil you are leaking. I hope that helps. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Terry Lund
February 11, 2018
Clothes are still extremely wet after spinning. I have replaced belts, spring kit. If i pull the motor towards the front of the machine, (you can hear and see it spinning faster), during spinning it spins out the water fine, so do not think its the drain pump. Any help will be very appreciated
For model number LAT9706AAE
Hello Terry, thank you for your question. There is a speed control switch on the control panel that might be stuck, or not functioning. I would recommend checking that part first, and if that part is functioning properly you might want to check and/or replace the motor, and drain pump. I hope this helps!

Was this helpful?
Thank you for voting!
Nancy
January 25, 2019
When washer goes to spin the hose connecting to water pump collapse and won't drain, could it be the pump or the hose.
For model number mat12PDLAW
Hi Nancy, Thank you for your question. If the hose is collapsing, it may not be fastened tightly. This can restrict water flow and increase the pressure on the hose. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Becky
August 14, 2019
My repairman has replaced both belts on my washer because it did not completely drain. It agitates fine and when spinning clothes to drain does not spin at high rate completely leaving clothes water logged. Do I need pump replaced also? Transmission replaced??
For model number LAT9706AAE
Hello Becky, Thank you for the question. If the tub is spinning slowly you may need to check the Tub Bearing Kit PartSelect Number PS2347235, The Rear Bearing PartSelect Number PS11739437 and the break assembly, PartSelect Number PS11743016. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Part Videos

Replacing your Maytag Washer Drain Pump

Replacing your Maytag Washer Drain Pump play video
Customer Repair Stories
 Average Repair Rating: 3.7 / 5.0, 25 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Leaking water
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.

So I got the model number and googled online. I found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.

Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.

Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.
194 of 220 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was not being removed from the wash tub after the spin cycle
I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.
  • John from Fort Lauderdale, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
  • Parts Used:
    WP6-2022030
48 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Strange noises - drum not always emptying
Found a very stretched, loose pump belt. Was able to pull it off pump pulley and motor pulley easily. Pushed motor assembly toward transmission pulley and removed wider drive belt. Wiped all pulleys clean. There's a double on the motor- one for drive belt, one for pump belt. Removed two hoses from pump using nutdriver. Removed pump. New pump installed. Installed two hoses on new pump. Installed drive new drive belt. Installed pump belt last. Slid pump to near farthest spot in slots. Tested for correct tension by pinching pump belt. Should be able to pinch center so two pump belt sides come within 1/4" of each other just as the spring tensioned motor mount starts to move. Pused washer back into place after external hoses connected. All new hose washers and filters on both hot and cold. Ran, checked for leaks - none! Absolutely perfect. Put front panel back on. No weird noises and drum empties perfectly every time. My wife is so pleased she's doing more loads.
  • Kenneth from Sunnyvale, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
  • Parts Used:
    WP6-2022030, 12112425, 12112425
23 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't let the water spin out!
I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks
  • SHARON from DETROIT, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
  • Parts Used:
    WP6-2022030
21 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak
Tilted the washing machine back at 45 degree angle. Removed three screws from the underside of machine. Slipped belt off pump. Lessened two hose clamps and removed hoses.
Lifted old pump out. Dropped new pump in place.
Screwed in the 3 screws. Slipped on the belt.
Attached two hoses. Tightened hose clamps.
Set washing machine upright.

No more leak.
My problem was I could not prove the pump was the source, but after switching it out I have had no problems (good enough).
  • richard from Tarzana, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
  • Parts Used:
    WP6-2022030
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The pump starting leaking around the center portion.
The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.
  • Kenny from Covington, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
  • Parts Used:
    WP6-2022030
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer did not drain.
Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.
  • Basil from St. Charles, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
  • Parts Used:
    WP6-2022030
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Standing water in washer tub
Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).
  • James from Baton Rouge, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
  • Parts Used:
    WP6-2022030
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was leaking from under the front of the washer when it was used.
After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.
  • Greg from Manhattan, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
  • Parts Used:
    WP6-2022030
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washing machine very noisy took belt off pump and it was normal.
I tipped the washer up on 2by4 blocks used 1/4 inch rachet with 5/16 socket two remove 3 screws and the belt from underneath. Took clamps off hoses yahoo saved l00 bucks!
  • Russell from Bayside, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
  • Parts Used:
    WP6-2022030
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
5.0
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
    Sort by:
    Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11743017
      Manufacturer Part Number: WP6-2022030
      Brand
      Model Number
      Description
      Maytag
      6329
      Washer - MAYTAG AUTOMATIC WASHER
      Maytag
      6349
      Washer - MAYTAG AUTOMATIC WASHER
      Maytag
      6359
      Washer - MAYTAG AUTOMATIC WASHER
      Maytag
      A100S
      Washer - Top Loading
      Maytag
      A101
      Washer - Top Loading
      Maytag
      A102
      Washer - Top Loading
      Maytag
      A102S
      Washer - Top Loading
      Maytag
      A103
      Washer - Top Loading
      Maytag
      A103S
      Washer - Top Loading
      Maytag
      A104
      Washer - Top Loading
      Maytag
      A105
      Washer - Top Loading
      Maytag
      A106
      Washer - Top Loading
      Maytag
      A106S
      Washer - Residential
      Maytag
      A107
      Washer - Top Loading
      Maytag
      A107S
      Washer - Residential
      Maytag
      A108
      Washer - Top Loading
      Maytag
      A108S
      Washer - Residential
      Maytag
      A110
      Washer - Top Loading
      Maytag
      A112
      Washer - Top Loading
      Maytag
      A15CA
      Washer
      Maytag
      A15CM
      Washer
      Maytag
      A15CT
      Washer
      Maytag
      A16CA
      Washer
      Maytag
      A16CM
      Washer
      Maytag
      A16CT
      Washer
      Maytag
      A17CA
      Washer
      Maytag
      A17CM
      Washer
      Maytag
      A17CT
      Washer
      Maytag
      A180
      Washer - Top Loading
      Maytag
      A181
      Washer - Top Loading

      Get in touch, we're here to help!

      Open until 1am EST

      Contact Customer Service