Single Drum Glide Felt Pad WP500121

Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.
The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!

Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.

Squeling from inside dryer. To Fix-
Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel.
Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.
Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.
Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.
Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!
Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.

I removed the lower front panel, which is held in place by two screws at the very bottom. I found pieces of the worn out brackets in the bottom of dryer. I then located damaged brackets bolted under front of drum at about 4&8 oclock. each bracket is held in place by two small bolts from the back side. The bolts for the new brackets go back in from the front, which eliminated the problem of stripped out holes. It is helpful if someone can reach indryer and hold up front of drum while you are starting bolts in brackets, I found that the kid standing closest worked great. The exploded view parts list was great for finding what I needed. My old dryer works great again and it is as quiet as a new one. This was $24.00 that was very well spent.

Very easy repair. I took off the bottom fromt panel with a nut driver. Then I took off the face/door panel. Take note of the wires that need to come off by marking them with a sharpie or tape. The top of the dryer can be stood up to allow access to the ductwork that has the felt pad on it. The felt pad was worn through in spots, the drum glide was completely gone and both cylinder glide brackets were almost completely worn through. I just replaced the brackets and the pads. The old felt came off fairly easily. I scraped the old glue for the felt off with a knife and cleaned and dried the surface before applying the hi temp adhesive. I waited 1 minute while the glue became tacky (be careful, the glue starts out thin and tends to run) and the felt pad was easily put back in place with my wife's help. Everything was very simple and it cost $87.00 for parts and shipping. I felt that this should be a good investment since I have had no other problems with this dryer and this is normal wear and tear. Better than paying $600+ for a new dryer. The video for changing the felt pad was very detailed and easy to follow as well.

Repair parts were exact OEM, went very smooth.
Longest part was cleaning the inside of dryer and cutting new vent pipe exit.

Watched YouTube video

removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.

Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.

Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced.
The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.