Whirlpool WP37001298 - Drum Glide | PartSelect.ca
Drum Glide – Part Number: WP37001298
( Grid squares measure 1x1 inch )
Drum Glide – Part Number: WP37001298 Drum Glide – Part Number: WP37001298 https://partselectca.azureedge.net/Schematics/Maytag/58910.gif

Drum Glide

Your Price

CAD$15.47

PartSelect Number PS11741931
Manufacturer Part Number WP37001298
Manufactured by Whirlpool

This part works with the following brands: Amana, Maytag, Speed Queen, Crosley, Magic Chef, Admiral.

This part works with the following products: Dryer.

This part fixes the following symptoms: Noisy | Will not tumble | Marks left on clothes

Videos For installing this part.

Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories

Average Repair Rating: 3.4 / 5.0, 49 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
David from Underwood, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
WPY54414, WP40113601, WP40111201, WP37001298, WP37001042, WP23748, 12002090, WP500121, WP233520
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.
158 of 228 people found this instruction helpful.
Was this instruction helpful to you?
Bryan from Everett, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Parts Used:
WPY54414, WP37001298, WP37001287, WP37001042, WP56076, WP40113601, WP23748
Dryer would make hmming noise and motor was loud like there was some resistance. Dryer would overheat and shut down
I removed the covers, released the belt, pulled the drum, replaced rollers, glides, idler pulley and motor. The motor was the main issue but I replaced the rollers, idler and glides while I was in there. My biggest challenge was the clips that hold the motor in place. The hooked over a metal ear. I was able to use a big strait slot with downward pressure to release and reinstall.

The illustratations on the web site made ordering the correct part easy and the part fit perfectly so this repair job could have been accomplshed by anyone with very basic mechanical understanding.

Thank you
89 of 155 people found this instruction helpful.
Was this instruction helpful to you?
Jeffrey from Medina, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
WP500092, WP37001298, WP37001132, WP37001036
Noisy - Clothes getting stuck between drum and bulkhead
1) Removed lower panel
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts

Dryer works great, is quiet again, and no longer eats clothes!!!!!!
80 of 92 people found this instruction helpful.
Was this instruction helpful to you?
russell from anamosa, IA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set, Wrench set
Parts Used:
WPW10116735, 61623, WP503979, WP40113801, WP40111201, WP37001298, WP37001287
would run but would not heat
removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat
46 of 1300 people found this instruction helpful.
Was this instruction helpful to you?
John from Litchfield, NH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Parts Used:
WP500121, WP37001298, WP37001287, W10856845, WP40111201
Idler Pully Squelling
Squeling from inside dryer. To Fix-
Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel.
Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.
Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.
Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.
Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!
Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.
19 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Chad from Caldwell, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
WPY055980, WP500092, WP37001298, WP37001132, WP37001036
Dryer made marks, then noise, then more noise
Thanks to this website we were able to not only find the parts, but a video that told us how to take the dryer apart. Unfortunately, between the time we diagnosed the problem, ordered the parts, and they arrived, the drum had worn into the front bulkhead. We were able to file the sharp parts dull and install the brackets, felt pads, and drum glides along with the felt seal, but ended up breaking the dryer door switch. Once that came in, it has been working. I'm not sure how long the repair will last, but it was much better than buying a new one.
18 of 501 people found this instruction helpful.
Was this instruction helpful to you?
joe from johnsburg, IL
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
WP500092, WP37001298, WP37001132, WP37001042, WP37001036
lots of noises
disassembled found bunch of worn out parts . I went to website wich was very helpful found all . my worn out parts online. dryer is very quiet now I wish i would have done it sooner.P.S. going to fix my dads dryer next. thank you
18 of 644 people found this instruction helpful.
Was this instruction helpful to you?
Dwight from Healdton, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
WP37001298, 12002090, WP500121
Dryer got very noisy (grinding sound), and would tear up items that got hung between drum and front panel
I removed the lower front panel, which is held in place by two screws at the very bottom. I found pieces of the worn out brackets in the bottom of dryer. I then located damaged brackets bolted under front of drum at about 4&8 oclock. each bracket is held in place by two small bolts from the back side. The bolts for the new brackets go back in from the front, which eliminated the problem of stripped out holes. It is helpful if someone can reach indryer and hold up front of drum while you are starting bolts in brackets, I found that the kid standing closest worked great. The exploded view parts list was great for finding what I needed. My old dryer works great again and it is as quiet as a new one. This was $24.00 that was very well spent.
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
christopher from sycamore, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
Parts Used:
WPY055980, WP37001298, WP37001132, WP37001036, WP500121
Dryer banging and clothes getting stuck between tub and felt pad while tumbling.
Very easy repair. I took off the bottom fromt panel with a nut driver. Then I took off the face/door panel. Take note of the wires that need to come off by marking them with a sharpie or tape. The top of the dryer can be stood up to allow access to the ductwork that has the felt pad on it. The felt pad was worn through in spots, the drum glide was completely gone and both cylinder glide brackets were almost completely worn through. I just replaced the brackets and the pads. The old felt came off fairly easily. I scraped the old glue for the felt off with a knife and cleaned and dried the surface before applying the hi temp adhesive. I waited 1 minute while the glue became tacky (be careful, the glue starts out thin and tends to run) and the felt pad was easily put back in place with my wife's help. Everything was very simple and it cost $87.00 for parts and shipping. I felt that this should be a good investment since I have had no other problems with this dryer and this is normal wear and tear. Better than paying $600+ for a new dryer. The video for changing the felt pad was very detailed and easy to follow as well.
11 of 381 people found this instruction helpful.
Was this instruction helpful to you?
David from Pasadena, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
WPY055980, WP40111201, WP37001298, WP37001132, WP37001036
Was not drying properly. Making a rubbing noise metal to metal sound.
First had to remove the front panel after lifting the top up on its hinges and supporting it. Diconnected wires to the front panel after marking them where they go. Saw where drum was rubbing above the impeller housing for the fan. Removed the drum slides and replaced them with new slides and brackets. Removed the belt and replaced it. It is a little tricky with the belt on the tensioner so pay close attention on how you remove it, it will make putting the new one on easier.Replaced the felt gasket with high temp glue. Cleaned inside and outside of cabinet. Put the panel back on,hooked up the wires and it looks and runs like new again.
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
2 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

Brand
Model Number
Description
Admiral
ADE7005AKW
Dryer - Residential
Admiral
ADE7005AYW
Dryer - Residential
Admiral
ADE9005AGW
Dryer - Residential
Admiral
ADG7005AWW
Dryer - Residential
Speed Queen
AEM197
Dryer - Residential, Automatic
Speed Queen
AEM377
Dryer - Residential, Automatic
Speed Queen
AEM397
Dryer - Residential, Automatic
Speed Queen
AEM407L
Dryer - Residential, Automatic
Amana
AEM407L2
Dryer
Speed Queen
AEM407L2-PAEM402L2
Dryer - Speed Queen Dryer Model AEM407L2-PAEM402L2 (AEM407L2PAEM402L2, AEM407L2 PAEM402L2) Parts
Speed Queen
AEM407W
Dryer - Residential, Automatic
Amana
AEM407W2
Dryer
Speed Queen
AEM407W2-PAEM402W2
Dryer - Speed Queen Dryer Model AEM407W2-PAEM402W2 (AEM407W2PAEM402W2, AEM407W2 PAEM402W2) Parts
Amana
AEM427L2
Dryer
Speed Queen
AEM427L2-PAEM427L2
Dryer - Speed Queen Dryer Model AEM427L2-PAEM427L2 (AEM427L2PAEM427L2, AEM427L2 PAEM427L2) Parts
Speed Queen
AEM427W
Dryer - Residential, Automatic
Amana
AEM427W2
Dryer
Speed Queen
AEM427W2-PAEM427W2
Dryer - Speed Queen Dryer Model AEM427W2-PAEM427W2 (AEM427W2PAEM427W2, AEM427W2 PAEM427W2) Parts
Amana
AEM477L2
Dryer
Speed Queen
AEM477L2-PAEM477L2
Dryer - Speed Queen Dryer Model AEM477L2-PAEM477L2 (AEM477L2PAEM477L2, AEM477L2 PAEM477L2) Parts
Speed Queen
AEM477W
Dryer - Residential, Automatic
Amana
AEM477W2
Dryer
Speed Queen
AEM477W2-PAEM477W2
Dryer - Speed Queen Dryer Model AEM477W2-PAEM477W2 (AEM477W2PAEM477W2, AEM477W2 PAEM477W2) Parts
Speed Queen
AEM497L
Dryer - Residential, Automatic
Amana
AEM497L2
Dryer
Speed Queen
AEM497L2-PAEM497L2
Dryer - Speed Queen Dryer Model AEM497L2-PAEM497L2 (AEM497L2PAEM497L2, AEM497L2 PAEM497L2) Parts
Speed Queen
AEM497W
Dryer - Residential, Automatic
Amana
AEM497W2
Dryer
Speed Queen
AEM497W2-PAEM497W2
Dryer - Speed Queen Dryer Model AEM497W2-PAEM497W2 (AEM497W2PAEM497W2, AEM497W2 PAEM497W2) Parts
Speed Queen
AEM677L2
Dryer