This idler shaft retaining ring is well under an inch long and is made of metal.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Dryer Idler Shaft Retaining Ring
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer, Washer Dryer Combo, Mixer.
This part works with the following products:
Maytag, Whirlpool, Kenmore, KitchenAid.
Part# WP354987 replaces these:
AP6008708, 3-12958, 312958, 354987, 3934678
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 18 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer Squeeked for a short time when first started
Took the two screws out of the front of the dryer. Tilted the bottom out until the clips in the top came loose. Disconnected the door switch and put the front panel aside. Removed 4 screws holding front drum support in place using small socket set. Pulled drum support off and set aside. Took note of how the belt ran through the idler pulley, pulled up idler pulley until the belt slipped off idler and motor pulley. Drum pulls straight out of dryer. With the drum out there is plenty of room to get to the screw holding the idler pulley arm in place, remove it so you can pull the old pulley and washers off shaft. Reassemble using new parts and reattach idler arm. Put the drum back in place, wrap new belt around drum (non groove side against drum), thread the belt around the motor shaft and work it back around the idler pulley. This was the hardest part of the job since your working in tight quarters and you can only fell what your doing. One the belt is in place, rotate the drum by hand to make sure the belt tracks properly. Finish cleaning up any dust accumulation inside the dryer/fan assembly. Reattach the front drum support, reattach the door switch wires and reassemble the front panel by tilting the panel until the top catches, swing down into place and attach bottom with the two screws. Done!
dryer was noisy, tumbler rollers and shafts wore out
disassembled dryer and removed and replaced rollers and shafts and installed new belt while i was at it. very easy fix, ordered parts from PARTS ELECT.COM , excellent website with great views of my machine made it east to order correct parts.very fast delivery , will use partselect again! HIGHLY RECOMMEND
Did an on-line search on Matag dis-assembly, pulled front panel, dryer drum, replaced idler pulley, rollers and belt. Also, vacuumed dryer cabinet , now the dryer works like new. This is an easy repair for anyone with any mechanical ability, and just basic tools.
The drier tumbler stopped spinning, and my wife noticed a burning smell when it ran.
1) Took off the front door of the drier (first unscrewed it in the sides, then lifted the door to lift the hinges up and pulled the door off) 2) Pulled the front panel down and off 3) I checked the belt to see if it was broken and it wasn't 4) I tried to turn the drier barrel manually to see if I can move the belt... it didn't move. Not knowing if there was just too much resistance, I tested the drier while looking at the motor and motor pulley as it ran. 5) I noticed that the motor pinion rotated, but the belt was slipping against it... that's why it smelled. The rubber was burning 6) Then I found that the idler pulley had stopped rotating, and the belt actually cut a channel into part of the plastic... That's when I realized that I had to replace at least the idler pulley. 7) Not knowing whether the bushing and other parts were going to be salvageable, I ordered parts for the whole assembly... but I wasn't sure how to best approach the repair... 8) Then I found partselect.com, and they had both diagrams of the assembly, all the parts easy to order, and best of all, a video of someone actually going through this repair! I was dumbfounded! :) 9) For swapping the parts I just watched the video on how to pull out the drier barrel... the only difference is that I didn't see a need to unplug the cables from the front top panel before removing the drier tumbler. (Obviously the power was turned off :P) 10) when I removed the barrel, I swapped the whole idler pulley assembly, just keeping the original spring. 11) Put everything back together, and it ran like a champ!
The video helped me save a lot of time though... it showed me how the whole thing is most easily serviced and made the repair a breeze!
If your dryer is squeaking it is most likely either the idler pulley or drum rollers. First I took apart the dryer to see which parts I would need. I checked the drum rollers by spinning them with my hand to see if they spun freely and also checked them to see if they were loose, they were okay. Then I checked the idler pulley and found my problem, it was hard to spin it so I figured the bearing was shot. I sprayed some lubricant on the bearing to help with the squeaking while I waited for my parts. It took about 30 minutes to diagnose my problem and put the dryer back together. I took some advise from another story saying to get the whole idler arm, shaft and pulley assembly. It might have cost me a few bucks more, but I did not want to run into the same problem he did (the pulley bearing was fused to the shaft). It took me about 20 minutes to take apart the dryer, install the part, and put it back together. If you are pretty good with fixing things, you should have no problem doing this repair.
Dryer made very loud squealing, screeching noise. (Sometimes Intermittent, sometimes constant)
Note: You may want to consider replacing the 2 Drum Support rollers at this time (while your in there)
1. UNPLUG YOUR DRYER FIRST.
2. Using a phillips head screw driver - Remove 2 screws that secure the dryer door hinges to the frame, Lift door very slightly to unhook hinges and pull out door with hinges attached as straight as possible, set aside. Remove the 2 plastic tabs from the opposing side of the door hinge also secured by screws.
3. Remove the front panel (panel is shaped like a football goal post) by tilting out the top ends of the front panel toward you, then lift up to remove panel from the bottom metal retaining tabs.
4. Remove the 2 hexhead screws from the 2 retaining clips (security hooks) that secure the top of the dryer closed.
5. Systematically remove the hexhead screws from the rest of the front of "shroud" (it holds (suspends) the drum in place between the front and back of the dryer).
*** I didn't disconnect any wires, I carefully swung out each piece that had wires attached, propped up those parts vertically ensuring no strain on the attached wires. Others may want to disconnect wires to avoid breaking or damaging them.
6. Vacuum out any dust/lint that may be present.
7. Draw a quick diagram of how the underside of the belt is threaded on the idler pulley and motor pully first. Release the tension of the belt from the underside of the drum. The easiest way is to push the idler pulley arm away from the belt and slide off the belt from the idler pulley and motor pulley. Slide the drum out.
8. Remove the hexhead screw from the bottom of the idler arm. Disconnect from retaining spring.
9. You may only need to replace just the Idler Pulley Wheel. I recommend replacing as a "unit" the Idler Pulley Wheel, Idler Arm, Ring-E and Idler Shaft Washer(s) - then you can just swap out the old one for the new one.
10. Reassemble
(When reassembling the belt - place around drum first and slide drum in place. Now from the underside-place (drape) belt around the motor pulley (it will be very loose) Now push the idler pulley arm toward the motor pulley, engage the left side of the belt around the idler pulley and slowly allow idler pulley to increase its tension on the belt) You can test manually by rotating the drum by hand to ensure proper movement.)
Took off face of dryer (two lower screws below door in front) and then removed the drum which gave me access to the idler arm and idler pully. Vaccumed the interior to remove dust and lint. Replaced idler arm and idler pulley assembly. Replace old belt as drum was reinstalled. Opened rear access panel to complete final routing of the new belt over idler pulley and drive motor. Turned the machine on to check repairs and function. Closed rear access door. Pushed dryer back into place and re-leveled machine.
Dryer was giving an irritating high pitched noise.
I won't get into too much of the tear down, as others have already given, in great detail, that information. I will say if I had not read the other repair information, I would not have known to replace the tensioner wheel, otherwise called the Idler pulley wheel and bearing. After using some machine oil to grease the shaft, I replaced the Idler Pulley wheel and the belt, and rebuilt the dryer. Runs as good as new.
After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.
Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeri
May 1, 2018
What is the size of the e-clip that holds the idler pulley assembly wheel on?
For model number LDG5005AAE
Hi Jeri, Thank you for the question. Very sorry but Whirlpool has not provided the size of the e-clip. I can verify the PartSelect Number: PS11741848 is the correct part for the model number provided. Hope this helps!
Was this helpful?
Thank you for voting!
Danielle
17 days ago
DOES NOT SPIN SOUNDS LIKE IT WANTS TO BUT DOESENT
For model number RAX7244KQ0
Hi Danielle, thank you for contacting us. We would suggest checking the motor coupling, part number PS1485646. It provides a cushioned connection between the transmission and the motor shaft. You may need to replace it to fix the issue. We hope this solves your problem!
This sleeve is less than an inch in diameter. It is made of metal and is intended for use with the screw that holds the idler pulley of your clothes dryer.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741848
Manufacturer Part Number: WP354987