Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Theresa H - February 18, 2024
Verified Purchase
Easy Repair!
The part was in great condition and arrived quicker than expected!
★★★★★
★★★★★
Daniel M - June 29, 2023
Verified Purchase
repair part
part was exactly as the original, worked well
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
A faulty computer
First remove the top of this particular dryer, to get to the necessary screws. computer is located on the left side, and 3 screws frees it up. Then disconnect the wires. Unscrew the board, and replace!! That simple!! Unfortunately for me the bad computer melted part of the wire harness. I called maytag and drove them nuts untill they paid to replace the wire harness. I learned two simple lessons. Buy the cheapest appliances you can find because everything is made like crap these days, and if you must buy the more expensive appliances, get the extended warranty because everything is made like crap these days!!!!! Thanks partselect.com for the info, and discount prices!!
Other Parts Used:
keri from lincoln park, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
37 of 45 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat
1. Unplug or turn off circuit breaker to dryer. 2. Remove two screws on the back of dryer that secure the dryer case top. 3. Slide the dryer case top to the rear of dryer and then lift to remove. 4. Electronic Control Board is located in the left side front corner, remove the three screws holding the Control Board and cover. 5. Unplug all wiring from Control Board and remove the one screw holding the board to the metal cover. 6. Reassemble with new Control Board in reverse order. 7. May you be blessed with dry clothes ever after.
Other Parts Used:
Dana from CHICKASHA, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not run
Excellent. Pulled top cover an exposed the control board. Replaced it just like a piece to a puzzle.
Other Parts Used:
Delmar from PHILADELPHIA, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The board went out.
Took off the top and took out 3 screws that held the board in. Unplugged all the connectors and plugged the new board in and put cover back on board and put the screws back in. And put top on.
Other Parts Used:
JANET from MORRILL, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
April 27, 2018
When my dryer gets to the end of a dry cycle, it stops and then comes back on. The digital display has a "[ ] going around in circles and the chime does not chime. Do you have any idea what the cause of this would be?
For model number NED7200TW
Hello Steve, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: moisture sensor, high limit thermostat, thermistor, thermal fuse and the electronic control board. You can test the parts with a multimeter. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
April 30, 2018
This isn't a question, but i wanted to comment on the last question i submitted, but didn't know how. We found a tutorial online that showed how to do some checks on each component and somehow it apparently cleared the faults on our dryer. We started it back up and it worked. Lucky.....i guess.
For model number NED7200TW
Hi Steve,
Thank you for the follow up! We are happy to hear that your diagnostic check cleared the issue that you were having. Thank you for sharing that with us. Hopefully this will help other customers as well. Have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
