Lid Hinge Pin

I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.

easily found correct parts at good price on parts select, ordered. Received the next day and repairs went smoothly, about 20 min and we were good as new.Saved us a repairman visit. thanks.

Unplugged Dryer; used screwdriver to push in and release two clips that hold top to front, tilted top back and removed two screws holding front to sides. Disconnected door switch and removed front .
Reached in above motor to remove belt from around pulley and tensioner wheel, Pulled drum and belt out of machine.
Removed approximately 10 screws around perimeter of blower housing and removed cover to access blower wheel. Removed outer lock ring from shaft and clamp from blower wheel hub, and removed blower wheel.
Took out tensioner assembly.
Disconnected wiring connector from motor.
Removed three screws that held blower housing to bottom and removed retainer around rubber motor mount at pulley end of motor. Lifted out motor, blower housing and vent pipe as one unit.
Removed 2nd outer lock ring from motor shaft.
Rotated motor frame 45 degrees to free the rubber mount from the blower housing.
Screwed new pulley onto new motor shaft and cleaned blower housing and vent pipe.
Assembly is reverse of disassembly.
Inspected and lightly greased the glides and inspected the idler wheels before reinstalling drum.

Dryer works perfectly.

Five to ten minutes also spent unscrewing and replacing timer knob and hinge pins on lid of matching washer Crosley cw22b5v.

Very simple repair.

First I popped the lid up to about 70 degrees. Then removed the two hinges. Then removed and replaced the two hinge pins. The key is to then just start the two screws for the hinges, slip the pins in and then tighten the hinge screws. Total time was 5 minutes.

This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge.
Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.

First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.

I lifted top portion of the washer after removing rear attachment screws to obtain access to lid hinge and mounting pins. I unscrewed the broken hinges and pins and installed the new ones.

I believe I could have avoided removing the rear attachement screws by sliding a screw driver or flat pry bar under the front panel and lifted the front panel up. The job would have taken much less time.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot