This part senses how much water is in the tub and allows it to reach the desired level. For example: A little water equals little pressure and a lot of water means more pressure inside the switch.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not drain
This part works with the following products:
Washer.
This part works with the following products:
Samsung, Maytag, Amana, Inglis.
Part# WP34001324 replaces these:
AP6008429, 34001324, DC97-03716C
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
OE error. All i read indicated the need for new sensor, but it did not correct the problem.
My husband simply removed the old sensor and put the new one in. It was not difficult.
Other Parts Used:
LISA from PRINCETON, WV
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
8 of 30 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andy
November 6, 2023
Water overfilling and overflowing out of the soap/softener dispenser drawer
Checked the sensor and when I blow into the sensor I can hear the diaphragm moving but I get continuity across the two outside terminals regardless of the movement. I’m thinking the contacts inside the part must be fused.
For model number MAH8700AWW
Hi Andy, thank you for your question! When a soap drawer leaks it will be almost invariably for one of two reasons, either the incoming water pressure is too high causing water to spill this is a case of too much water is flowing and the water cannot drain through the dispenser hose fast enough. Or something is blocking the flow of water. First, check to make sure that your dispenser is draining properly, and it is not clogged. Clean out the dispenser and softener compartment. Pour a cup of water into the softener compartment quickly until it starts to overflow. It should then siphon the water out and if so, that means the unit is definitely clean. If the dispenser is clean, then you need to replace your water inlet valve, part number PS11741549. This water valve has multiple solenoids. One for the softener and one to fill the tub. The solenoid that fills the tub can be working normally while the softener solenoid will fail, causing water to spill over the top. Good luck with this repair!
Replace drain pump, I'm still error code[no drain] purchased the pump from your company.
For model number NFW7200TW10
Hi Felix, Thank you for the question. The ND (no drain) Error just indicates there is an issue in the draining cycle. Excess suds can cause this error as well. Try running the washer through a rinse cycle without clothes or soap and add a cup of white vinegar to flush the system, then run another load with just water. You can also check the drain hoses for clogs or blockages. Also check the pressure switch hose to make sure it is clear. You can also test the control board with a Multi Meter to see if it is getting 110-120VAC. And the Water Pressure Switch for proper resistance. Check Voltage at Pin #6 and #7 of CN3. Check Voltage and Frequency at Pin #6 and #8 of CN3. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kreatha
November 7, 2019
My drain pump is only getting 3volts. What causes this? Thank you
For model number MAH8700AWW
Good Day Kreatha. Thank you for your question in regards to your unit (Model Number MAH8700AWW). Based on our research your drain pump (PartSelect Number: PS11741568) may be worn out and may have to be replaced. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
