Part Location Diagram of WP3362952 Whirlpool Bleach Dispenser - White
See part 11 in the diagram
Replacing your Whirlpool Washer Bleach Dispenser - White
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Bleach Dispenser - White

★★★★★
★★★★★
6 Reviews
$12.00
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11741235
Manufacturer Part Number WP3362952
Manufactured by Whirlpool
Product Description

Bleach Dispenser - White Specifications

This part holds the bleach until it is ready to be released into the cycle.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Whirlpool Washer Bleach Dispenser - White

Replacing your Whirlpool Washer Bleach Dispenser - White
Troubleshooting
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Roper.
Part# WP3362952 replaces these:
AP6008104, 3362952, 387028, 387029, 63289, 63401, 63402, 63405, WP3362952VP
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
5.0
Filter By Rating:
  • 5 Stars
    6
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.3 / 5.0, 14 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.
Other Parts Used:
Tub Spring Direct Drive Water Pump
  • RICHARD from PHILA, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
840 of 907 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Parts replacement
Changing the parts was easy.
Other Parts Used:
Lint Filter
  • Juan from Frisco, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
41 of 1286 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator slipping
Removed bolt in center of agitator then slid agitator straight up and out replaced the dogs and the other parts that came with the cam kit i also replaced a few of the other parts that wear in the agitator ,you can actually re-cut the teeth on the dogs with a razor so that they will work again ,but new parts are very reasonably priced and the parts arrived very quickly the next day .
Other Parts Used:
Seal, Inner Cap Spacer, Thrust Washer Agitator Cam Kit
  • Nick from Castro Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
16 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
pump leaking, agitator not turning
First I went to this site and read what everyone had to say on leaking pumps. After finding the model number, I looked at the parts list, and found what parts I thought I would need. First I shut off the water and unpluged the washer Replacing the water pump was very easy after reading what other people had done. I pulled the washer out from the wall about 18 inches and tilted back on a 45 degree angle. The pump was now in plain sight and helt in with two slide clamps. Using a pair of plyers I remover both clamps from both hoses on the pump. By pushing to the outside of the pump I was able to remove both of the slide clamps. This allows the pump to be lifted out and off the motor shaft. As my washer had just started leaking " about one week" the pump slid off the shaft easy. There was no rust on shaft. Pump shaft has a slot in it so the pump can only go on one way. By reversing the way I removed the pump I was able to slide the new pump back onto the shaft and slide the slip clamps back over the pump. Replacing both hoses and both clamps. Now pump was in place. I pulled the washer away from the wall and slid back into place. That took care of the pump. For the top side I removed the top part of the agitator by pulling up and removing the part that holds the softner. Under this was a piece of plastic that I was able to lift out. Under that was a 12MM bolt with a rubber washer. Using a scoket set I removed the bolt and washer. Lifting up on the agitator it came right out. Pulling on each end of the agitator I was able to pull it apart. Inside was a large plastic washer and agitator directional cogs all in one piece. This piece just lifts up and off. I replaced the old piece with the new on and slid the two agitator back togeather. Setting the agitator back into the washer and put the 12mm bold and rubber washer back on. Then I put the plastic back on and set the top softer cup back in place. Snapping in the bleach dispenser was very easy, just shap into place. Pluging the washer back in, and turning back on the water I ran the washer with no clothes in it so I could check for leaks and make sure everthing was working. Repairing both parts took about 30 minutes and now the washer is like new.
Other Parts Used:
Agitator Directional Cogs Bearing, Cam Driven Direct Drive Water Pump Agitator Cam Kit
  • Becky from Oskaloosa, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob Broke
Ordered part and within 2 days it arrived. Removed broken knob and twisted new one on. Awesome job getting the part to me so fast. Thank you!
Other Parts Used:
Timer Knob
  • Tammy from Elgin, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noticed agitator wasnt moving during wash and rinse cycles. Prior to repair no strange smell or noises
Went online to Parts Select and typed in Model #. Looked thru repair help and found very simular problems. I did disassemble the upper prtion of the aggitator by removing softner dispenser. Once inside I used a shoe string and routed it thru the two handles on the plastic cover and pulled up moderately, exposing the cam and doggs. I used a 7/16" socket on a 6" xtension to reach the mounting bolt. Slowly turn bolt counter-clockwise holding the lower agitator. Once the mounting bolt was out I temporarily replaced the plastic cover. I pulled up on the UPPER agitator to completely remove it from the tub. Once set on a firm surface I again pulled out the plastic cover ,bolt and cam cover, exposing the cam and dogs. I shook them out. I replaced everything with what was included in the agitator repair kit ( great kit). Everything for assembly is as the instructions state and totaly a reverse process. Take care not to over tighten the bolt. I did take this oppurtunity to clean the tub and agitators. I did also remove the lower agitator to clean the area. Thanks Parts Select!
Other Parts Used:
Agitator Repair Kit CORD-POWER
  • ARTHUR from FT HUACHUCA, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set, Wrench set
4 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repair went well!!!
Repairs went well.....it took less than 10 mins...just followed picture diagram....and test....and it worked well>>>.
Other Parts Used:
Agitator Cap Barrier with Seal Agitator Bolt Agitator Cap Agitator Repair Kit Thrust Spacer
  • Michael from Bakersfield, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Existing bleach dispenser was cracked
1- Ordered and received a new bleach dispenser.
2- Removed broken dispenser from machine.
3-Dropped in new dispenser.
Viola! It was fixed and no more random left over bleach stains on non-bleach loads of laundry! :-)
Other Parts Used:
  • Deborah from San Diego, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken anchor piece
Installed long end first and snapped it into place.
Other Parts Used:
  • Neal from BRADENTON, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator not Agitating
Remove Agitator cap and inner cap. Unscrew center retaning bolt. Lift out agitator assembly. Remove thrust washer and ratchet assembly. Install ratchet and thrust washer in top of agitator. Set agitator on shaft. Install and tighten center retainer bolt. Install inner and top caps. Load it up, and REALLY wash some clothes.
I have been fixing appliances and a many other mechanical things since my early teens.
When I went to the CONTRACTOR’S store, they treated me like a young dumb kid that shouldn’t be allowed to buy repair parts, or the part is unavailable. Thanks to the Internet and places like PARTSELECT.COM, I can buy the parts I need and not have to call a shysters repairman to rip me off. PS.com provided me with the parts I wanted without disputing me. They also provide simple, clear, and to the point instructions for replacing the old parts. Even someone doubting their own ability can handle a complicated repair. PS.com not only has the major parts that fail, like motors, but also the little things like switches, knobs, trims, handles, seals, and all the other minor parts.
Other Parts Used:
Thrust Spacer
  • Kenneth from Winnemucca, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
FRANK
June 18, 2019
It is a KitchenAid supubra. The bleach dispenser will not drain. It has a hose connection that runs back to under the control panel. It is not the simple plastic tub with a hole in it. I tried cleaning and reeming out the hole, but no luck. Suggestions??
For model number KitchenAid sm8525121 washer
PartSelect logo
Hello Frank, thank you for writing. You may need to replace either it or the hose connection to it, but we were unable to locate a parts list for your model number. Please verify the number you provided us. If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part! We look forward to hearing back from you.

Was this helpful?
Thank you for voting!
Larry
July 12, 2019
Can I get a fabric softener dispenser for this machine? Thank you.
For model number ATW4475TQO
PartSelect logo
Hi Larry, thank you for your question. According to your model number unfortunately it does not. I hope that helps. Good luck with your repair.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741235
Manufacturer Part Number: WP3362952
Brand
Model Number
Description
Kenmore
1101050299
Washer - Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer
Kenmore
11012502100
Washer
Kenmore
11012852100
Washer
Kenmore
11014502300
Washer
Kenmore
11014852300
Washer
Kenmore
11015732400
Washer
Kenmore
11015842400
Washer - Kenmore Washing Machine
Kenmore
11015852400
Washer
Kenmore
11015862400
Washer
Kenmore
11015864400
Washer
Kenmore
11016512690
Washer
Kenmore
11016512691
Washer
Kenmore
11016512692
Washer
Kenmore
11016602690
Washer
Kenmore
11016602691
Washer
Kenmore
11016602692
Washer
Kenmore
11016602693
Washer
Kenmore
11016611690
Washer
Kenmore
11016611691
Washer
Kenmore
11016611692
Washer
Kenmore
11016612690
Washer
Kenmore
11016612691
Washer
Kenmore
11016612692
Washer
Kenmore
11016732500
Washer
Kenmore
11016812500
Washer
Kenmore
11016812501
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service