Ice Maker Water Fill Tube Kit

Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done.

first thing i did was to turn off the water supply line to the frig,then pulled it away from the wall and removed the cardboard backing at the bottom of the frig.
then i loosened the nut on the supply line to the fill valve removed the two screwsholding in the fill valve,un hooked the two electrical plugs.[i had allready disconected the electric when i pulled the frig out]then i un hooked the other two water line conected to the fill valve,replaced the valve with the new one rehooked everything . the ice machine tube was only a matter of loosining up the nut on the tub takeing off the two nuts on the back of the frig the just pull out the old tude install the new one rehook the water line ,turn the water back on check for leaks get all the air out of the line by using the water despencer in the door and your good to go .

We rolled the refrigerator out away from the wall and it was obvious where the break was located. We took out the old water spout for the ice maker and replaced the tube and the tubing from the solenoid. We turned it on and soon we had water dripping everywhere. We unloaded and defrosted the freezer which got all of the remaining ice that was stuck in there. We put everything back together. I read in some instructions in the manual that it might take 24 hours for the ice maker to reprogram itself and start producing ice. I was only about 12 hours and we had ice again and everything worked well. You really do not have to disconnect the water from the main line, the solinoid controls that part of operation and turns the water off until the ice trays are free and clear.

JLB

Parts went right into place as the pictures showed and was working again in about 30 minutes. The only thing that wasn't working was the ice took forever to make, but solved that problem by turning up the temp in the freezer.

The problem was discovered to be a cracked fill tube head, This part extends behind the refigerator and is VERY vulnerable to breakage when the box is pushed backagainst a wall space! Placing a shim under the vertical part of the fill tube fixed the problem even without replacing it with the new part. So, now I have a spare!

The repair I performed was so simple it doesn't merrit mentioning. What I was really impressed with is finding a source this easy and user friendly (even though they didn't have the dishwasher soap dispenser I needed). The parts were easy to find on your site and because of your simple methods of finding and describing your parts I was able to buy a markedly better filter at a cheaper price than my usual source. They may have the same part but because they are oriented to showing you only the specific part you request rather than showing you all options, like your site, I wound never have known that filter existed. Thank you for a good resource.

The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.

Shut off water supply line, and turn off ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.

Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.

first bought new ice maker installed it-didn`t fix the problem. next bought fill tube kit and dual outlet vale -installed those ice maker works GREAT no leaks -no ice froze together in bend. thanks for the help GUYS.

I first ordered the wrong part number and received a 2 way valve, but after talking to customer service they provided me with the correct part number for the correct 3 way valve and gave me an RMA to return the wrong part. I disconnected the power and turned off the water and removed the old valve. The new water inlet valve had slightly different water tubing self compression connections, so I had to cut off the old tube nuts with a pair of dikes on my existing tubing and simply push the trimmed tubing all the way into the new valve connection ports. After connecting the new water inlet valve, I checked for leaks and found none. I also had to remove my internal ice maker to remove all of the frozen ice. After reinstalling, the next day my ice maker was making ice again. In the mean time I had also ordered a new ice maker, which I probably do not need now. I can't decide whether to keep it for a spare or to request an RMA.

this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?