This part is the replacement dispenser lever retainer for your refrigerator. It is made of metal and is approximately 2 inches long and ½ an inch wide. The bottom half of the dispenser lever retainer holds in the pivot points of the ice and water arms. If it breaks, the arms will be loose and can shake around. The top half springs the ice and water arms back into the original position, and if the retainer is broken, they will not be able to do this. The dispenser lever retainer is found behind the dispenser trim and can be removed with a ¼ inch nut driver. This part is sold individually and is an OEM part.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Refrigerator Levers Retainer/Clip
Troubleshooting
This part fixes the following symptoms:
Not dispensing water | Leaking
This part works with the following products:
Refrigerator.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Maytag.
Part# WP2194719 replaces these:
AP6006118, 2180201, 2183783, 2194719
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Frank T - February 27, 2019
Verified Purchase
Lever retainer
Followed your online installation video for a quick and easy repair. Thx Frank
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix. I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites. Thanks, Ron
Other Parts Used:
Ron from Newton, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
34 of 45 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
ice maker and water dispenser would not work due to switch clamps being broken off the control plate
remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ran around 30 with shipping.
Deli slides broken both sides / door closer cam fridge side
Remove drawer then shelf removed sliders both sides installed new slides / remove door shelves empty butter tray remove upper hinge remove door remove lower hinge replace cam clean area reassemble
Other Parts Used:
William from Dayton, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Greg
November 12, 2019
Does this part weaken over time approx.12yrs
For model number RS25AGXNQ02
Hello Greg, Thank you for the question. Yes, the clips can become worn over time and need to be replaced. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Rosa
January 5, 2022
Water despenser shoot out the water to hard,missing a plastic tubing can I order the part
For model number KSRP25FNWH00
Hi Rosa,
Thank you for your question. The part number listed under your model number for the water dispenser fitting and tube assembly is PS886371. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. When replacing the water lines, also check the water pressure. If it is too high you will need to adjust it. We hope this helps! If you have any questions, please let us know.
