Average Repair Rating: 5.0 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Lid trigger went and fried both plug and connector
Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.
Other Parts Used:
barbara from MILLVILLE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chelsey
July 29, 2019
This part does not come with the metal contacts inside the plug. The reason the plug needed replacing is because the contactors are fried. Do you sell the contacts separately?
Hello Chelsey, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Clayton
June 28, 2022
I have a estate whirlpool washing machine model ETW4400VQ1 and the wire connector that fits into the lid switch has melted, does the wire connector work for this whirlpool top load washer.
For model number ETW4400VQ1
Hello Clayton, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11738986. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Marc
February 17, 2023
Washer only fills with water. Nothing turns the motor on to wash or to drain or to spin in any cycle selection or wash/spin selection. There's no humming. It acts as if there was a blown fuse to the motor. Last use, it filled halfway with water and when agitater was supposed to start it just seemed to go dead. But if I turn the water selector for more water it adds it. I'm dumbfounded!
For model number 110.29892990
Hello Marc, thank you for contacting us. You may need to check the following parts first, to solve the issue: the timer, part number PS11742062, lid switch assembly, part number PS11742021, and the motor switch, part number PS11746107. If the issue persists, it means that there is something wrong with any of the parts of the motor. So, we recommend you check the motor coupling, motor start capacitor, and clutch assembly, to fix the issue. For replacement, these parts are available at our site with part select numbers PS1485646, PS11746661, and PS334641 respectively. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
