Whirlpool WP215235 - Injector Tube | PartSelect.ca
Injector Tube – Part Number: WP215235
Injector Tube – Part Number: WP215235 Injector Tube – Part Number: WP215235 https://partselectca.azureedge.net/Schematics/Maytag/37308.gif

Injector Tube

Your Price

CAD$17.13

PartSelect Number PS11738907
Manufacturer Part Number WP215235
Manufactured by Whirlpool

This injector tube is a little over two inches long. It it white and made of plastic.

This part works with the following brands: Maytag, Jenn-Air.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms: Leaking.

Questions & Answers
Installation Instructions Provided by PartSelect customers like you.
Average Repair Rating: 3.4 / 5.0, 3 reviews
What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Richard from Alexander City, AL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
WP215235, WP596669, WP215581, WP215233
Agitator Not Woking
Unplugged power cord then disconnected the water supply and drain hose. Removed 2 screws and took the front panel off. Laid washer on it's side and posistioned the transmission with the cover facing upward. Removed the hex head screws then used a razor knife and a putty knife to remove the silicone sealant. Found that the agitator shaft spring had broken and fallen into the housing jamming the gears that's used in agitation. Removed the oil and all broken pieces of the spring. Installed new shaft spring, replaced the oil then applied sealant to the cover and screwed the cover back down. Let the washer stay in the same posistion for about 18 hours to let sealant dry completely. Then I sat the washer back on it's feet and removed 2 screws that holds the top lid in place. This allowed me access to the tub cover where the injector t is located. Installed the injector t along with the injector tube seal. Connected the hose and hose clamp. Then I put the lid back down and secured with the screws. Connected the water supply and drain hose then the power and selected a wash time and observed the operation. Everything worked ok so I put the front cover back on. Note: I had used the injector t from this washer to fix another washer that an appliance dealer had given me to use for parts to repair the one just described above. That was the only thing that was wrong with it. It was used for about a year and a half and it developed a problem in the spin cycle. Appears to be a brake problem. I intend to repair it as well.
17 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Linn from El Segundo, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WPY215234, WP215235, WP215233, WP213013
Tub injector hose had hole in it from rubbing on side of cabinet.
Remove front panel of machine, 2 screws at
bottom. Remove 2 bolts at top front with nut
driver and whole top can be lifted to expose
all parts. Remove injector hose clamps and
clamp new hoses in place. I replaced both
injejctor hoses while open although only one
had small hole in it. This is the only repair
done on this coin-op machine in 20 years. At
this time I did replace both drive belts but they
could have run for more years, no cracks or
breaks in belts. This machine is in a 12 unit
apartment building. We have two on them,
same age. We purchased both coin ops new
in 1987.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Padraic from SAINT PAUL, MN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
WPY215234, WP216201, WP215447, WP215235, WP215233, WP213015, WP213013
Hot water overflow injector, ran onto floor
You will need 2 hose clamps not sold as maytag parts.

Remove front washer panel screws.

Remove bolts holding front of top to side panels

Remove hose clamp from front hose to injector sleeve.

Twist fill hose ccw 90 degrees at tub fitting to remove.

Clean corrosion at tub attachment point wuth wire brush.

Paint bare metal to seal. Allow to thoroughly dry.

Remove injector sleeve and injector hose.

Trim new injector hose to match length of removed hose (I cut off abt 4 inches)

Install injector hose and plastic sleeve. Ensure clocking is correct on hose.

Install gasket on fill hose fitting.

Insert fitting into tub. Rotate 90 deg CW to latch.

Install gear clamps loosely on fill tube.

Attach fill tube to fill fitting and injector sleeve.

Slide clamps onto tube ends ensuring clamp clocking provides access and clears tub top..

Test tub fill to ensure injector works without leaks
1 person found this instruction helpful.
Was this instruction helpful to you?

Model Cross Reference

Brand
Model Number
Description
Maytag
A104
Washer - Top Loading
Maytag
A105
Washer - Top Loading
Maytag
A112
Washer - Top Loading
Maytag
A183
Washer - Top Loading
Maytag
A190
Washer - Top Loading
Maytag
A1910
Washer - Top Loading
Maytag
A211
Washer - Top Loading
Maytag
A211S
Washer - Top Loading
Maytag
A212
Washer - Top Loading
Maytag
A212S
Washer - Residential
Maytag
A23CA
Washer
Maytag
A23CDL
Washer - Commercial
Maytag
A23CDW
Washer - Commercial
Maytag
A23CSL
Washer
Maytag
A23CSW
Washer
Maytag
A23CT
Washer
Maytag
A24CA
Washer
Maytag
A25CA
Washer
Maytag
A25CAE
Washer
Maytag
A25CM
Washer
Maytag
A25CME
Washer
Maytag
A25CS
Washer
Maytag
A25CT
Washer
Maytag
A26CA
Washer
Maytag
A26CAE
Washer
Maytag
A26CD
Washer
Maytag
A26CDC
Washer
Maytag
A282
Washer - Top Loading
Maytag
A283
Washer - Top Loading
Maytag
A284
Washer - Top Loading