Product Description
Rubber Foot Pad Specifications
This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Washer Rubber Foot Pad
Troubleshooting
This part works with the following products:
Washer, Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag, International, Jenn-Air, Amana.
Part# WP210684 replaces these:
AP6005800, 2-10684, 210684, WP210684VP
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Les O - January 24, 2021
Verified Purchase
easy repair
best to heat in hot water first. becomes very pliable and east to put on. feet are not Maytag branded but fine. expensive for me in Canada even though they came from Canada. 78 dollars with tax and shipping. worth it tho'. washing machine operates like it's stuck to the floor. you must make sure all feet are firmly planted on the floor by rotating them. my machine is old and the old rubber pads no longer grabbed the metal feet making it hard to level. I put 2x4 piece under machine to completely remove the feet. cleaned the threads and lock nut then applied new pads and replaced feet into threaded holes.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 5 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..
Other Parts Used:
-
Paddy from Ferndale, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
57 of 81 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Seal failure, leading to bearing failure
Not much to add to others' descriptions of the repair except for two things- one, the procedure for removing the front shroud on a stackable unit is somewhat different than what is described in the seal kit directions. The door switch assembly gets in the way; though the whole repair can be done by one person, it would be better (and safer) to have a second person helping at least during this part. The whole shroud is unwieldy, with two drain hoses attached, along with two dispenser hoses, the door switch/light, and the side & bottom mounting brackets, and it has to be eased out one step at a time. During the last part of this you will have to lift up the front of the dryer at the same time.
Second, our particular washer has a 90xxxx serial number. The bearings are Chinese-sourced, not the good NSK bearings. Though the listed bearing numbers are the same... the rear bearing is held in by a retainer that is permanently fixed into the outer tub. There is no easy way to drive the bearing forward, either, as the retainer covers nearly all the bearing outer shell. The chances are very high that the outer tub would be damaged beyond repair if the retainer or bearing was removed. Fortunately in this washer, the back bearing was still in reasonable shape and had some grease left; I was able to pop out the grease seal and re-pack it with wheel bearing grease. The front bearing & seal are replaced as others have described. The front bearing takes a majority of the load, so others may have similar wear.
This washer was only 3 1/2 years old; we bought six Maytag appliances at the same time, and four of the six have had major repair problems (two were cheaper to replace than repair). That, and the $678 replacement cost of the outer tub, explains why the Maytag repairman is so lonely...
Second, our particular washer has a 90xxxx serial number. The bearings are Chinese-sourced, not the good NSK bearings. Though the listed bearing numbers are the same... the rear bearing is held in by a retainer that is permanently fixed into the outer tub. There is no easy way to drive the bearing forward, either, as the retainer covers nearly all the bearing outer shell. The chances are very high that the outer tub would be damaged beyond repair if the retainer or bearing was removed. Fortunately in this washer, the back bearing was still in reasonable shape and had some grease left; I was able to pop out the grease seal and re-pack it with wheel bearing grease. The front bearing & seal are replaced as others have described. The front bearing takes a majority of the load, so others may have similar wear.
This washer was only 3 1/2 years old; we bought six Maytag appliances at the same time, and four of the six have had major repair problems (two were cheaper to replace than repair). That, and the $678 replacement cost of the outer tub, explains why the Maytag repairman is so lonely...
Other Parts Used:
-
James from Chillicothe, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped leveler screw making impossible to level my washer
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.
Other Parts Used:
-
Rebecca from Wylie, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
22 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Warn out foot pads
Pried off old pads - used hammer to tap on new pads.
Locating replacement parts was the problem until I found partselect.com
Locating replacement parts was the problem until I found partselect.com
Other Parts Used:
-
Dennis from Granada Hills, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt was hard and made a squeaking nosie, rubber pads were o good because of age.
First I disconnect the electrical power, 2nd disconnect the vent tube, 3rd removed the four screws on the back of the dryer, 4th removed the front panel and disconnect the wires for the door switch, 5th remove the cover that holds the drum inplace, 6th remove the belt, 7th vacum all parts to remove any lint and dirt from the inside of dryer, 8th reassemble the parts in the reverse order. this took me about 55 minutes from start to finish. The parts were right which made the job very easy. The rubber foot pads were easy, just remove the old ones and install the new ones. Thank you for the right parts.
Other Parts Used:
-
Coyote Custom Builders from Phelan, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
December 22, 2019
Will part 210684 fit my Maytag model la510 which is quite old ( built in about 1980)
For model number La510
Hello Mike and thank you for writing.
Yes, Part Number: PS11738859 is in the list of compatible items for your model. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Mike
December 22, 2019
On my previous question about the leveling leg pads i forgot to mention that they are about one and one-half inches in diameter
For model number La510
Hello Mike and thank you for writing.
That sounds right. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738859
Manufacturer Part Number: WP210684
Manufacturer Part Number: WP210684
Brand
Model Number
Description