SENSOR

Hello Hubert, thank you for your question. Oven temperature sensors are very easy to replace. The sensor is located inside the oven at the top left or right hand side of the interior. Locate the sensor, then follow these instructions. I hope this helps! Step 1: Shut off power to the oven. ... Step 2: Remove the mounting screws. ... Step 3: Access the wire connector. ... Step 4: Disconnect the wire harness. ... Step 5: Install the new temperature sensor probe. ... Step 6: Restore power.

Hi Patricia, Thank you for the question. very sorry but we do not have a video for this part as of yet. Here are some installation instructions. Hello Hubert, thank you for your question. Oven temperature sensors are very easy to replace. The sensor is located inside the oven at the top left or right hand side of the interior. Locate the sensor, then follow these instructions. I hope this helps! Step 1: Shut off power to the oven. ... Step 2: Remove the mounting screws. ... Step 3: Access the wire connector. ... Step 4: Disconnect the wire harness. ... Step 5: Install the new temperature sensor probe. ... Step 6: Restore power. Hope this helps!

Hello Penny, Thank you for the question. I suggest testing the Sensor. At 70 degrees the resistance should be 9.3K ohms, 90 degrees would be 7.7K ohms. at 100 degrees would be 6.2K ohms, and 120 degrees would be 4.3K ohms. If the thermistor reads outside of range then it needs replaced. Hope this helps!

Hello Ellen, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Manufacturer Part Number W10833885. We hope this helps.

Hi Bernard, Thank you for your question. If the oven is not heating correctly, the issue may be with the oven sensor. The oven temperature sensor is the part that monitors the oven temperature and signals the electronic control board to turn the elements on and off. Before removing this part from the oven and testing it with a multimeter for continuity, unplug the oven from the electrical outlet. A normal reading should be 1100 ohms, but as readings vary from model to model, you will need to reference your owner’s manual to determine what the correct reading should be. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. If the sensor is fine, you will need to check the elements, the electronic control board and the wiring between the parts to see which one is causing the issue. We hope this helps with the repair!

Hi Sarah, thank you for contacting us. If your safety thermostat is shutting down at a lower temperature than usual, it means your temperature sensor, part number PS11726314, is not giving the right command to the control board. Replacing the sensor seems like a solution in this case. We hope this solves your problem!

Hello Frank, thank you for your inquiry. Based on our understanding of the issue, we would suggest you check the oven bake igniter, part number PS11752876. When the glowing igniter gets weak, it does not provide the right amount of current to the gas valve. This causes the igniter to only open slowly, thus allowing gas to escape and no ignition to occur in the first seconds. With a new igniter in place, the oven should ignite during the first 15–30 seconds, and there should be no gas smell. We hope this is helpful!

Hello Sarah, thank you for your inquiry. To fix this issue, the following parts need to be checked: the safety thermostat, part number PS11740991, and the bake element, part number PS11703285. If the issue still exists, then you may need to check the electronic control board, part number PS12074595. We hope this sorts out your problem!

Hello Tony, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

Hi Dean, Thank you for the question. I suggest testing the sensor. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!