Part Location Diagram of W10833885 Whirlpool SENSOR
See part 26 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

SENSOR

★★★★★
★★★★★
7 Reviews
$170.30
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11726314
Manufacturer Part Number W10833885
Manufactured by Whirlpool
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Oven is too hot | Oven not heating evenly
This part works with the following products:
Range.
This part works with the following products:
Whirlpool, Maytag, KitchenAid, Jenn-Air.
Part# W10833885 replaces these:
W10586204
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
7 Reviews
5.0
Filter By Rating:
  • 5 Stars
    7
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 2 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Oven would heat up very slowly and not reach more than 325 *F
I purchased all the likely suspects. It was a corroded lower heating element that was faulty. Fixed the burnt out light bulb for good measure while I was in there.
Other Parts Used:
Terminal Block Safety Thermostat Light Bulb - 40W
  • Andrew from BOTHELL, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
12 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven temperature was WAY off, sometimes 50 degrees.
Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.

The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.

I had found a good YouTube video and didn't use the app.
Other Parts Used:
  • Sarah from Raleigh, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

16 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hubert
February 6, 2018
Is this difficult to replace the sensor ps11726314
For model number wee730hodbo
PartSelect logo
Hello Hubert, thank you for your question. Oven temperature sensors are very easy to replace. The sensor is located inside the oven at the top left or right hand side of the interior. Locate the sensor, then follow these instructions. I hope this helps! Step 1: Shut off power to the oven. ... Step 2: Remove the mounting screws. ... Step 3: Access the wire connector. ... Step 4: Disconnect the wire harness. ... Step 5: Install the new temperature sensor probe. ... Step 6: Restore power.

10 people found this helpful.

Was this helpful?
Thank you for voting!
Patricia
February 7, 2018
Is there a step by step video?
PartSelect logo
Hi Patricia, Thank you for the question. very sorry but we do not have a video for this part as of yet. Here are some installation instructions. Hello Hubert, thank you for your question. Oven temperature sensors are very easy to replace. The sensor is located inside the oven at the top left or right hand side of the interior. Locate the sensor, then follow these instructions. I hope this helps! Step 1: Shut off power to the oven. ... Step 2: Remove the mounting screws. ... Step 3: Access the wire connector. ... Step 4: Disconnect the wire harness. ... Step 5: Install the new temperature sensor probe. ... Step 6: Restore power. Hope this helps!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Penny
May 23, 2019
Starts to heat but not reaching the temperature to bake. Is it the safety thermostat: Wp3196548 Or the sensor: W10833885
For model number YWFE715H0EE0
PartSelect logo
Hello Penny, Thank you for the question. I suggest testing the Sensor. At 70 degrees the resistance should be 9.3K ohms, 90 degrees would be 7.7K ohms. at 100 degrees would be 6.2K ohms, and 120 degrees would be 4.3K ohms. If the thermistor reads outside of range then it needs replaced. Hope this helps!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Ellen
February 5, 2020
Will this part fit my oven? Part #w10833885 or should I use part # w10779716. My stove is a "slide in" model.
For model number WEC530H0DS0
PartSelect logo
Hello Ellen, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Manufacturer Part Number W10833885. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Bernard
January 27, 2023
Hello, the temperature of the oven takes a very long time to increase to 350 degrees and the control board does not show the temperature when it lowers in the oven. Should I replace the sensor and what is the ohm reading I should read to see if it is defective. If I order a part and it is not correcting the problem, can I return it for a refund.
For model number kseg950ess1
PartSelect logo
Hi Bernard, Thank you for your question. If the oven is not heating correctly, the issue may be with the oven sensor. The oven temperature sensor is the part that monitors the oven temperature and signals the electronic control board to turn the elements on and off. Before removing this part from the oven and testing it with a multimeter for continuity, unplug the oven from the electrical outlet. A normal reading should be 1100 ohms, but as readings vary from model to model, you will need to reference your owner’s manual to determine what the correct reading should be. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. If the sensor is fine, you will need to check the elements, the electronic control board and the wiring between the parts to see which one is causing the issue. We hope this helps with the repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Sarah
March 6, 2023
The safety thermostat doesn't make sense. The temp is too low at a wide range of settings. At 350 it might be 320, at 450 it might be below 400. I'd hoped the new sensor would fix this. That bake element is incorrect for my oven. I've already replaced the heating element / convection fan. The control board is $600+ so I don't want to put out that kind of money and that not fix it either!
For model number Kitchenaid KSDB900ESS0
PartSelect logo
Hi Sarah, thank you for contacting us. If your safety thermostat is shutting down at a lower temperature than usual, it means your temperature sensor, part number PS11726314, is not giving the right command to the control board. Replacing the sensor seems like a solution in this case. We hope this solves your problem!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Frank
September 18, 2023
Smell raw gas every time turning the oven on and the heat seems to be not strong and it takes a long time when on bake selection
For model number KSGG700ESS1 KitchenAid Stove
PartSelect logo
Hello Frank, thank you for your inquiry. Based on our understanding of the issue, we would suggest you check the oven bake igniter, part number PS11752876. When the glowing igniter gets weak, it does not provide the right amount of current to the gas valve. This causes the igniter to only open slowly, thus allowing gas to escape and no ignition to occur in the first seconds. With a new igniter in place, the oven should ignite during the first 15–30 seconds, and there should be no gas smell. We hope this is helpful!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Sarah
March 3, 2023
I've replaced the sensor with this one and the oven temperature is still often significantly below the reading, though on occasion it is correct. I use two oven thermometers to confirm the actual temperature. Plus, you can feel when it's 40+ degrees cooler. Any suggestions?
For model number Kitchenaid KSDB900ESS0
PartSelect logo
Hello Sarah, thank you for your inquiry. To fix this issue, the following parts need to be checked: the safety thermostat, part number PS11740991, and the bake element, part number PS11703285. If the issue still exists, then you may need to check the electronic control board, part number PS12074595. We hope this sorts out your problem!

Was this helpful?
Thank you for voting!
Related Parts:
Tony
April 22, 2018
Problem with oven is that originally turns on when the flames goes away it doesn't comes back it give a clicking sound as if it want to come back
PartSelect logo
Hello Tony, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

Was this helpful?
Thank you for voting!
Dean
May 1, 2018
The oven is very slow on pre-heat. Using a thermal gun to check the temp it shows a much higher temp in the oven than what the readout on the control panel shows. Would the sensor in the oven be the problem? Ps things will burn when we cook at recommended temp and time.
For model number WFG515S0EW0
PartSelect logo
Hi Dean, Thank you for the question. I suggest testing the sensor. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!

Was this helpful?
Thank you for voting!
  • 1
  • 2
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11726314
Manufacturer Part Number: W10833885
Brand
Model Number
Description
Kenmore
66442793710
Range - Kenmore Elite 66442793710 Electric Range
Kenmore
66475113610
Range - GAS RANGE
Kenmore
66475113611
Range - Gas Range
Kenmore
66475123610
Range - GAS RANGE
Kenmore
66475123611
Range - Gas Range
Kenmore
66475223710
Range - Kenmore Elite Gas Range
Kenmore
66475223711
Range - Kenmore Elite Gas Range
Kenmore
66495113610
Range - ELECTRIC RANGE
Kenmore
66495113611
Range - Electric Range
Kenmore
66495113612
Range - Electric Range
Kenmore
66495223710
Range - Kenmore Elite 66495223710 Electric Range
Kenmore
66495223711
Range - Kenmore Elite 66495223711 Electric Range
Kenmore
664C95113610
Range - ELECTRIC FREE STANDING
Kenmore
664C95123610
Range - ELECTRIC SLIDE
Kenmore
664C95123611
Range - Electric Range
Kenmore
66542783710
Range - SLIDE
Amana
AGR5630BDB2
Range - GAS RANGE
Amana
AGR5630BDS2
Range - GAS RANGE
Amana
AGR5630BDW2
Range - GAS RANGE
Amana
AGR6303MFB0
Range - GAS RANGE
Amana
AGR6303MFS0
Range - GAS RANGE
Amana
AGR6303MFW0
Range - GAS RANGE
Amana
AGR6603SFB0
Range - GAS RANGE
Maytag
AGR6603SFB1
Range
Maytag
AGR6603SFB2
Range
Maytag
AGR6603SFB3
Range - Range
Whirlpool
AGR6603SFB4
Range - Range
Amana
AGR6603SFB7
Range - Amana Range/Stove/Oven Agr6603sfb7
Amana
AGR6603SFB8
Range
Amana
AGR6603SFS0
Range - GAS RANGE
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service