Part Location Diagram of AEN73131406 LG Clutch Housing Assembly with Mode Shifter
See part K170 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Clutch Housing Assembly with Mode Shifter

★★★★★
★★★★★
1 Review
$331.09
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11708484
Manufacturer Part Number AEN73131406
Manufactured by LG
Product Description

Clutch Housing Assembly with Mode Shifter Specifications

This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive system between the appliance spin and agitate cycles. Is measures 14.5 inches in diameter. You may need to replace this part if you hear strange noises or if the washer will not spin or agitate.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
LG, Kenmore.
Part# AEN73131406 replaces these:
AP5975369, 3661EA1009D, 3661EA1009E, 3661EA1009F, AEN73131403, AEN73131411
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
4.0
Filter By Rating:
  • 5 Stars
    0
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 5 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
LOUD GRINDING/ROARING NOISE, INTERMITTANT SPIN
Watch this video on youtube:https://www.youtube.com/watch?v=8ZKgP6hu8Fk very similar

Keep all parts separate and in order in a plastic box with dividers
1. Disconnect washer from wall. (electrical and hot/cold hoses, drain tube)
2. Remove center cap from bottom tub plate
3. Remove small bolt under cap
4. Remove bottom Tub Plate
5. Remover washer
6. Remove larger 38mm nut (I bought the correct deep well socket) Ive seen other video use a pipe wrench)
6a. Remove the large washer under nut
NOTE- I did not remove the tub, total hassle, found it unnecessary, Yes the washer was heavier but nothing that cant be managed.
7. Place a blanket on the floor and lay the washer on its back to access the bottom.
NOTE Everthing is nuts and bolts at this point. 10mm socket worked on all
8. Remove Nut & washer on rotor. Remove rotor-its has a line of magnets and the edges are sharp. Just wiggle it a bit. wear gloves if need be.
9. Remove bolts from Stator, user a small flat blade screw driver to undo 1 or 2 (some) electrical connections. Lay the stator aside. Move the electric connector(s) out of the way.
10. Remove the grounding wire at 6 oclock position
11.Remove the rectangular pack and the 3 oclock position by removing 2 bolts. It has a small arm that reaches out to the clutch arm, slide the piece out to the widest part of hole in clutch arrn an wiggle it loose.
Almost there....
12. Remove all the 10MM headed bolts from the clutsh and drive assemble The inner bolts are a slightly different style, keep the two sets separate.
13. Remove the clutch and drive.

NOTE: if the drive doesnt come out with a slight pull, you have missed a bolt(s)-inspect and remove as need be

14 Wipe clean the pocket in the outer wash tub that accepts the seal on the top of the drive. Lubricate the new drives seal completely with a little dishwasher detergent so it slides smoothly and seals well.

15. Assembly is the reverse:

Last Notes:
*Install all bolts for the clutch and drive hand tight as you get everything lined up.
*Once all bolt are in the clutch and drive are hand tight, tighten the bolts in a cross pattern as you would a wheels lug nuts
*Snug the bolts used to attached the clutch and drive firmly 1/8 to 1/4 turn past snug
*Make sure you clock the stator to the correct position, again hand tighten bolts then final tighten in a cross pattern.
*The nut and washer in the rotor tighten to 1/4 to 1/2 turn past snug, its tight.
*The large 38 MM nut on the top of the drive assembly torque is 88 ft lbs. Have a partner or friend hold the tub while you torque the large nut. If you don't have a torque wrench you can rent one from a number of auto-part chain stores.
*I used a 1/2 Impact gun to remove the 38mm nut, Never use that kind of power to reassemble as it will damage parts.


Good luck, you can do it.
Other Parts Used:
  • MIKE from LANDENBERG, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Direct drive shaft broke right under the agitator plate.
Removed the inner tub laid the washer on its side with a blanket under it and Removed the assembly then the shaft assembly.
Installed the new assembly and re assembled the rest of the washer (top and bottom) and plugged it in. Works great. TIP: you will need a big socket set for the tub retaining nut.
Other Parts Used:
  • EDWIN from FELTON, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lots of loud noises when washing and spinning.
Getting the old part out was not too hard, but had a couple challenges. Watched a video from RepairClininc that detailed the process very thoroughly. Definitely use an impact gun to remove the drum nut inside the drum. My drum was stuck on the shaft pretty good. Would not lift off. Removed the rotator, stator and diverter motor on the bottom, and took out all the bolts securing the clutch. Had to use a hammer to tap the shaft out from inside the drum. Then the clutch dropped out the bottom and I was able to remove the drum. Installation went smooth. Just remember the order you took stuff off and the position of the parts. They need to go on the same or the electrical connectors won't reach.
Other Parts Used:
  • Ken from CALDWELL, ID
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had no problems
I can’t really say it was easy and I just did it
Other Parts Used:
  • Sharron from RICHMOND, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set, Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer making noise when washing. rinse and spin was normal.
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Other Parts Used:
  • David from BOTHELL, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

4 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Armando
December 6, 2021
My Lg washer shows a repetitive banging sound, which is particularly bad on a spin cycle. I have had this washer for 8 years already.
For model number wt1101cw
PartSelect logo
Hi Armando, Thank you for your question. If your washer is shaking and moving, the suspension rods that secure the tub are likely worn and need replacing. The part number listed under your model number for the suspension assembly is PS8749609. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Martin
April 11, 2022
will a bad bearing / clutch assembly cause screeching sound and leaking water?
For model number wt5720c
PartSelect logo
Hello Martin, thank you for writing. The screeching sound is made but a faulty Clutch Housing Assembly with Mode Shifter part PS11708484. The leaking water is likely a hose or Washer Water Inlet Valve PS1237472. The Tub to pump hose is PS3617213 and the drain hose is PS8749199. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.

Was this helpful?
Thank you for voting!
Related Parts:
Jeff
December 7, 2023
My drum has a little excessive play and clunks a little when manually rotated back and forth. Wondering if this play would be in the clutch or another part?
For model number Wt5070ocw
PartSelect logo
Hello Jeff, thank you for reaching out to PartSelect. We have concluded that the issue is with the drive shaft and shifter assembly, part number PS11708484. We recommend replacing it to fix the issue. Good luck with your repair!

Was this helpful?
Thank you for voting!
Cathy
February 29, 2024
Washer was making a loud sound but now it won’t spin. It just keeps filling back up with water then drains water but does not go into spin cycle
For model number WT5270CW
PartSelect logo
Hi Cathy, thank you for reaching out. We would suggest checking the drive shaft and shifter assembly, part number PS11708484. It connects the motor with the wash plate and shifts the drive system between agitate and spin. You may need to replace it to fix the issue. We hope this sorts out your problem!

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11708484
Manufacturer Part Number: AEN73131406
Brand
Model Number
Description
LG
048231013369
Washer Dryer Combo - Washer-Dryer
LG
048231013635
Washer Dryer Combo - Washer-Dryer
LG
29002
Washer Dryer Combo - Washer-Dryer
LG
29272
Washer - Washer
LG
29472
Washer - Washer
LG
31402
Washer - Washer
LG
31412
Washer Dryer Combo - Washer-Dryer
LG
31422
Washer - Washer
LG
31423
Washer - Washer
LG
31433
Washer Dryer Combo - Washer-Dryer
LG
31463
Washer - Washer
LG
31512
Washer Dryer Combo - Washer-Dryer
LG
31513
Washer - Washer
LG
31522
Washer Dryer Combo - Washer-Dryer
LG
31552
Washer Dryer Combo - Washer-Dryer
LG
31553
Washer - LG Washing Machine Model 31553 Parts
LG
31622
Washer - LG Washing Machine Model 31622 Parts
LG
31623
Washer - LG Washing Machine Model 31623 Parts
LG
35302
Washer Dryer Combo - Washer-Dryer
LG
35452
Washer Dryer Combo - Washer-Dryer
LG
35563
Washer Dryer Combo - Washer-Dryer
Kenmore
79629002000
Washer
Kenmore
79629002010
Washer
Kenmore
79629272000
Washer
Kenmore
79629272010
Washer
Kenmore
79629272900
Washer
Kenmore
79629278000
Washer
Kenmore
79629278010
Washer
Kenmore
79629278900
Washer
Kenmore
79629472000
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service