This lint filter screen has two side guides on either either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide
$74.77
In Stock
Order within the next 6 hrs and your part ships today!
Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts.
*** Note: Per manufacturer this kit has been upd...
This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.
$17.35
In Stock
Order within the next 6 hrs and your part ships today!
This part is the replacement thermal fuse for your dryer. It measures a little more than an inch wide, and about ¾ inch long. The thermal fuse is a safety device that shuts off the burner in a gas dry...
$50.81
In Stock
Order within the next 6 hrs and your part ships today!
This is the replacement motor pulley for your dryer. The motor pulley transfers momentum from the drive motor to the drum via the drive belt. If the motor pulley cracks or is no longer staying on the ...
$84.81
In Stock
Order within the next 6 hrs and your part ships today!
This blower wheel is suitable for some clothes dryers of the 10 and earlier series. Manufactured to fit a 1/2 inch motor shaft, this blower wheel is 3-1/8 inches deep. The diameter of the wheel is 7-1...
$96.43
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for YE225LV
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.
This was an extremely easy repair and it save me lots of $$: (1) Disconnected power (2) Opened the top of the dryer (3) Disconnected wires to temperature sensor. (4) Used a 1/2" socket wrench with extension and a drill to remove 2 screws holding down the temperature sensor (5) Removed 1 screw holding down the heating element. (6) Removed wires connected to heating element and pulled out old element. (7) Reassembled new element. (8) Turned on empty dryer for 30 minutes to burn off smell from the new element.
1. Removed the screws from the lint catcher 2. Removed the bolts from upper rear of dryer 3. Pried off the dryer top from the front (it rests on rear hinges) 4. Disconnected dryer door wiring 5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses support) 6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance 7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler) 8. Placed new belt on tumbler; reinserted tumbler 9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first) 10. Made sure belt and tumbler seal were properly installed 11. Replaced parts in reverse order The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)