Models > WM2077CW

WM2077CW ((00)) LG Washer - Overview

Sections of the WM2077CW

[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Washing Machine Drain Pump – Part Number: 4681EA2001T
Washing Machine Drain Pump
★★★★★
★★★★★
(75)
PartSelect #: PS3579318
Manufacturer #: 4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$156.41
  In Stock
Order within the next 11 hrs and your part ships today!
Water Inlet Valve - Hot – Part Number: 5220FR2006H
Water Inlet Valve - Hot
★★★★★
★★★★★
(15)
PartSelect #: PS3527427
Manufacturer #: 5220FR2006H
$75.94
  In Stock
Order within the next 11 hrs and your part ships today!
Water Inlet Valve - Cold – Part Number: 5220FR2075L
Water Inlet Valve - Cold
★★★★★
★★★★★
(9)
PartSelect #: PS11728995
Manufacturer #: 5220FR2075L
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$135.21
  In Stock
Order within the next 11 hrs and your part ships today!
Washer Door Boot Seal – Part Number: 4986ER0004F
Washer Door Boot Seal
★★★★★
★★★★★
(6)
PartSelect #: PS3524977
Manufacturer #: 4986ER0004F
Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore ...
$253.18
  In Stock
Order within the next 11 hrs and your part ships today!
Washer Hose with Bellows – Part Number: 4738ER1004B
Washer Hose with Bellows
★★★★★
★★★★★
(8)
PartSelect #: PS3523347
Manufacturer #: 4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$62.02
  In Stock
Order within the next 11 hrs and your part ships today!
SENSOR ASSEMBLY – Part Number: 6501KW2002B
SENSOR ASSEMBLY
★★★★★
★★★★★
(13)
PartSelect #: PS16556422
Manufacturer #: 6501KW2002B
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
$62.91
  In Stock
Order within the next 11 hrs and your part ships today!
Rear Tub Gasket – Part Number: 4036ER2004A
Rear Tub Gasket
★★★★★
★★★★★
(1)
PartSelect #: PS3522855
Manufacturer #: 4036ER2004A
$45.82
  In Stock
Order within the next 11 hrs and your part ships today!
Door Lock Assembly – Part Number: EBF49827801
Door Lock Assembly
★★★★★
★★★★★
(4)
PartSelect #: PS3533609
Manufacturer #: EBF49827801
$108.87
  In Stock
Order within the next 11 hrs and your part ships today!
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(6)
PartSelect #: PS3523345
Manufacturer #: 4738ER1002A
This hose has bellows to allow for flexibility during the wash and spin cycles.
$53.13
  In Stock
Order within the next 11 hrs and your part ships today!
Hose Assembly,Drain – Part Number: 5215ER2002G
Hose Assembly,Drain
★★★★★
★★★★★
(2)
PartSelect #: PS3527325
Manufacturer #: 5215ER2002G
$88.40
  In Stock
Order within the next 11 hrs and your part ships today!
Gasket – Part Number: 4036ER4001B
Gasket
PartSelect #: PS3522859
Manufacturer #: 4036ER4001B
$42.63
  In Stock
Order within the next 11 hrs and your part ships today!
Inlet Valve Assembly – Part Number: 5221ER1003A
Inlet Valve Assembly
★★★★★
★★★★★
(4)
PartSelect #: PS3527452
Manufacturer #: 5221ER1003A
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$137.79
  In Stock
Order within the next 11 hrs and your part ships today!

Questions And Answers for WM2077CW

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the WM2077CW

[Viewing 18 of 18]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing Fixing
Show All
Draining Issues
Fixed by
these parts
Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Locking Issues
Fixed by
these parts
Fixing
Show All
Engine runs but does not pump water
Fixed by
these parts
Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Not draining
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Parts Used:
Washing Machine Drain Pump
  • Jorge from Apple Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
568 of 726 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Parts Used:
SENSOR ASSEMBLY
  • Mark from Harrisburg, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
239 of 311 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn bearings
To replace the bearings a complete disassembly of the washer was required. After pulling the tube assembly from the cabinet and separating the tube enclosure halves and removing the rotor and stator, since the washer uses direct drive, a gear puller was required to push the drive shaft through the old bearings since they didn’t separate easily as seen in several YouTube videos. After removing the tube assembly it is recommended that you also separate from the spider, which contains the drive shaft, from the tube itself since a significant amount of sediment had caked inside the indentations on the inside of the spider. Since the front bearing, part number 4280FR4048D, was no longer available I used an NTN double sealed bearing, part number 6306LLUC3/L627. The only other tricky aspect of the repair was pushing the drive shaft through the new bearings since pushing it by hand did not produce enough force to get it through to expose enough of the shaft on the other side to be able to reconnect the rotor. The solution was to pull the shaft through rather than pushing it. To do this I placed a 1 3/4 inch drive socket over the outer ring of the rear bearing, and then I used a 3 inch 10mm x 1.50 mm bolt through the drive socket with enough large washers to use as spacers between the bolt head and the drive socket. I then threaded about a half inch of the bolt into the center of the drive shaft by hand to remove any gap between the bolt head and the washers. As I turned the bolt clockwise with a 17mm drive socket wrench the bolt pulled the drive shaft through the bearings with ease. I did follow the manufacturer’s recommendation to replace the seal between the two tube enclosure halves and the three dampers with new ones since they do eliminate much of the vibration during the spin cycle. I also replace the top bellows since I noticed that a large hole had been formed on it by rubbing against the inlet hoses which are situated directly above. The repair took a week only because I had to wait for parts.
Parts Used:
Gasket Shock Absorber Assembly
  • Anthony from Crystal Lake, IL
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
92 of 156 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!