This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$14.96
In Stock
Order within the next 1 hr and 30 mins and your part ships today!
The filter is made of metal and is intended for use with ranges and cooktops. As per the manufacturer, this filter may be 1/2" slimmer than the original, but will still function the same.
$39.13
In Stock
Order within the next 1 hr and 30 mins and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 1 hr and 30 mins and your part ships today!
This oven control board and clock is for ranges.
Oven control board and clock monitors the oven temperature and controls the oven heating functions in the range, and includes the digital display fo...
$529.69
In Stock
Order within the next 1 hr and 30 mins and your part ships today!
To convert back to Natural Gas - you must save old orifices. If you no longer have the old orifices, the burner tubes must be ordered that contain the natural gas orifices.
$47.21
In Stock
Order within the next 1 hr and 30 mins and your part ships today!
Questions And Answers for SVD48600W
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Debra
November 17, 2022
My oven clock and the the oven cancel do not work on my Jenn-Air range. Is it possible to order the front control panel and not just the clock? I’m able to turn off the oven by hitting bake then entering 0 for the temp. Do you have parts to fix this problem?
For model number SVD48600W
Hello Debra, thank you for the question. The control panel with the keypad, part number PS11743879, and the electronic clock control board, part number PS11743858, are two different parts. First, you will need to identify which part is malfunctioning. You can test the control panel either with a multimeter or by turning the stove off, unplugging the ribbon that connects the control panel to the electronic clock control board, and turning the stove back on. If any error codes or messages appear, replace the electronic clock control board, if not then replace the control panel. Hope this helps!
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step). Next, I removed the knobs from the front of the display panel. Then I removed the 4 phillip head screws that were located (1 each) behind the knobs. Finally, I removed the 4 hex head screws from the bottom of the front panel. You caan then remove the panel a few inches and remove the two cable connectors. The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable. The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse. If you did everything correctly, you should have a very bright stove clock again!