This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slid...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
$131.99
In Stock
Questions And Answers for MDB8969SDM0
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Doug
December 16, 2023
The circuit breaker tripped during operation. Went to reset the breaker and now the breaker trips as soon as it is turned on. What needs to be checked. I have the service technicians only tech sheet that came with the unit. But it does not mention this problem
For model number MDB8969SDM0
Hi Doug, thank you for contacting us. We would recommend checking the wiring. If it is shorted, we would recommend replacing the wire harness, part number PS11768175, to fix the issue. We hope this helps!
How do I clean the filter there is residue water when completed cycle
For model number MDB8969SDM0
Hello Ed, Thank you for your inquiry. You can remove the lower spray arm to access the accumulator and filter. You can simply rinse it with soap and water and a soft bristled brush. We hope this helps.
Circulation pump does not seem to be working. No water is spraying during the wash cycle
For model number MDB8969SDM0
Hello Jodee, thank you for your inquiry. We would recommend replacing the circulation pump, part number PS11723102, to fix the issue. We hope this sorts out your problem!
Hello Grag, Thank you for contacting PartSelect.com. Very sorry but we do not have the age of the appliance, just parts lists and diagrams. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the appliance directly. We hope this helps!
Was this helpful?
Thank you for voting!
Tony
May 26, 2022
My dishwasher heating element stays on, what is the best way to diagnose this problem and are there any common causes?
For model number MDB8969SDM0
Hi Tony,
Thank you for your question. If the dishwasher heating element will not turn off, a relay on the electronic control board is stuck in the closed position and it will need to be replaced. The part number listed under your model number for the electronic control board is PS10062738. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
