J322*01 General Electric Range - Instructions

Plug-in new element

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Due to this wall oven being vintage 1972, I decided to replace the broil element along with the bake element that had actually failed. The repair was pretty straight forward as seen on the videos, altough it can be somewhat tight to use screw drivers or nut drivers with long handles. You may find that shorty screw drivers or a 1/4 inch ratchet wrench and appropriate socket are easier to work with. There were two things that I was cautious about. The first was to be very gentle with the power wires since I didn't know what condition their insulation was in. I tried not to scrape them on the sheet metal opening as I pulled them gently out through the oven insulation. Secondly, I was very, very careful in moving the oven temperature sensor probe out of the way so I could undo the broil element. Before I started the job, I had learned that this probe isn't a separate piece part, it is part of the entire THERMOSTAT ASSEMBLY for the stove and it's not readily available. Furthermore, this assembly costs $250 to $350 !!!! The only negative with this job was that the old broil element has some kind of heat resistant material on the rear of the plate that attaches it to the oven wall. This old material fell apart during disassembly. I kind of pieced it back together during assembly, but I would have liked to have been told I needed this piece (since there wasn't an exploded parts view on the web for me to look at)or a new piece of this material should have been supplied as part of the broil element.

Used socket set to remove bolts holding the elements in place, then used a screw driver to remove the wires from the elements. Replaced with new elements, screwed in the wires and reattached the elements to the wall with the bolts.
It was easy, it was just a small space to work in.

Was able to slide it right in

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

Unplugged bad surface element and plugged in replacement.

The Surface Element on our GE stove made in the mid 70's finally gave up and would not heat. I went to several of the big home improvement stove with not luck in finding the right heating element for our stove so I turned to a local appliance stove that carries GE products, they did sell me an element and asured me it was the correct one, but once again the element was the wrong one. Then with a simple google search for GE replacment parts I found partselect.com. With the detailed description and images with measuring grids I was able to quickly find the correct heating element for me stove. I am very pleased and the stove is back to 100%.
Thanks partselect.com

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

First, turn off the power. Remove the two retaining screws, pull out the broken element far enough to unscrew the connectors, remove the element, reconnect the new element, screw it back in, turn the power back on. Yes, it is that easy! Took me all of five minutes. Took longer to find my tools!

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.