Models > IUD7555DS1 > Instructions

IUD7555DS1 Whirlpool Dishwasher - Instructions

All Instructions for the IUD7555DS1
121 - 135 of 451
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower Dishrack Wheel Replacement
Simply take out the lower dishwasher rack, grab a pair of pliers and gently pry the old assembly off and snap the new assembly into place. It's very easy.
Parts Used:
Lower Dishrack Wheel Assembly
  • Jeff from LAS VEGAS, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Parts Used:
Dishwasher Rack Track Stop
  • Ken from PEMBROKE PNES, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not sure
My Husband did it
Parts Used:
Lower Dishrack Wheel Assembly
  • Stanley P from ALBANY, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Parts Used:
Dishwasher Lower Spray Arm
  • Ginger from DONIPHAN, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door falls when opened
Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.
Parts Used:
Door Balance Link Kit
  • JOSEPH from LAMBERTVILLE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Parts Used:
Dishwasher Rack Track Stop
  • Tim from GLADSTONE, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I can not get the part to fit and stay in place.
It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.
Parts Used:
Dishwasher Rack Track Stop
  • Marilyn from TRINIDAD, CO
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Parts Used:
Dishwasher Lower Spray Arm
  • jeffrey from HOUSTON, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken plastic piece in door balance link kit
Watch video and followed instructions. Very easy!
Parts Used:
Door Balance Link Kit
  • Pauline from FERGUS FALLS, MN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken cord on door balance
Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.

Thanks,
Ted K.
Parts Used:
Door Balance Link Kit
  • Ted from Santa Clarita, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Door Leveler Nylon Cord assy broke
It was very easy.
Parts Used:
Door Balance Link Kit
  • Robert from Highland Village, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower spray arm had a small seam split forcing waves of water against the lower door causing water to leak out the door bottom.
After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.
Parts Used:
Dishwasher Lower Spray Arm
  • Cameron from DEFIANCE, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
If I can do it, you can do it.
Replacing the rear wheel assembly isn't as easy as replacing the front, which took 5 minutes. You have to align the tine row, so it takes a few minutes more. But I'm a tiny woman with long nails, and if I can do it, you can do it!

Just watch the video, follow the directions, and you can't go wrong.
Parts Used:
Lower Dishrack Wheel Assembly
  • Ellen from GREENWICH, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
removed and installed cords with screw driver
Parts Used:
Power Cord Kit
  • Ronald from VAN BUREN TWP, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Parts Used:
Door Latch - Black
  • Edna from WEST MONROE, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the IUD7555DS1
121 - 135 of 451