This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$31.99
In Stock
Order within the next 12 hrs and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$14.99
In Stock
Order within the next 12 hrs and your part ships today!
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$112.99
In Stock
Order within the next 12 hrs and your part ships today!
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
$166.99
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for GLEQ2152ES1
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rhonda
January 13, 2020
I start the dryer, it works briefly then shuts off and all of the lights flash and beeping.
For model number GLEQ2152ES1
Hello Rhonda,
Thank you for your question. Our sources suggest replacing the thermal limiter under part PS419402 for your model to fix the issues. We hope this helps!
Hello Lee, thank you for contacting us. We have researched the model you have provided and have found that the part you are looking for is part number PS1148434. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
What is error code 68? The controls come on by themselves and the display says error code 68. The controls come on constantly, so i turn off the power until i need the dryer.Thanks for your answer.
For model number GLEQ2152ES1
Good Day Inge. Thank you for your question in regards to your unit (Model Number GLEQ2152ES1). Based on our research, Error Code 68 means that there is a stuck key on your control board. If you are not able to free the key from it's position, the recommendation in to replace the control board. Hope this Helps! Best Regards.
Was this helpful?
Thank you for voting!
David
November 26, 2019
Dryer not selectable above low heat at any mode selection. Anything higher causes all right side lights to flash and beep.
For model number GLEQ2152ES1
Hello David, Thank you for the question. This sounds like an issue with a Defective Board PartSelect Number PS12724036 that needs to be replaced. Hope this helps!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.
