ADB1500AWW2 Amana Dishwasher - Instructions

1. Turned of Power via circuit breaker
2. Opened Dishwasher
3. Removed back of door (11) hex screws with electric driver
4. Removed latch assembly
5. Pried contacts from switches
6. One switch was more difficult to pry loose than the other
7. You will probably need a plier
8. Switch or connector may break but latch assembly comes with switches, so you just need to be careful not to break the connectors
8 Plugged connectors into new switches on latch assembly
9. Replaced latch assembly
10. Replaced door with (11) hex screws - two top screws hold assembly in place
11. Turned on circuit breaker and tested machine
12. Finished

Comments: This latch assembly was better constructed than the original and I expect it to last the life of the machine. If one of the switches wasn't so difficult to pry loose, then the repair would have taken ten minutes less to repair. Well worth the effort. Repair time was probably 20-30 minutes.

I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

You just remove the old unit and set in the new unit. the wheels were already connected.

Remove all the screws around the inside panel and separated by size and location. There are two larger screws for the bottom two holes. Marked the electrical connectors for location on the latch assembly. Also marked the top of the two microswitchs for easier reattachment. Removed the microswitchs with the needle-nose pliers and attached to the new assembley. Reattached electrical connectors and the plastic panel.

Removed all the screws from the door panel. Removed door handle. Replaced it with new handle. Attached switches but did not turn the power off. Replaced the panel. Everything fitted well and works well.

removed all door housing scews,removed old handle and wires and installed new 1,screwed housing back on,done

removed inside door panel--then the wire leads--replaced broken part--reattached wire leads --reattached inside door panel--done----------------suggestion--it would be a good idea to include with the new part the screwdriver bit to fit the screws on the door panel ---many people would not have that size Good service from this site

Super easy fix, watched the installation video, did the repair in about 15 min. Helpful site and will gladly return in the future if needed

Removed the front door cover (held by several screws) Replaced the broken latch with the replacement by reconnecting the switches (one at a time & noting their orientation). Rescrewed the cover. Works like a charm!

Turned of power at the circuit breaker first. Removed the hex nuts from the inside of the door. Latch is loose know and just need to unplug the power cords from both sides. Install new latch by reattaching the two power cords to it and reassemble. Very easy and very fast shipping had part the next day with regular shipping.

Turned off the power at the panel board. Took off the front panel. (The screws are torque screws, so you need that kind of driver). Removed the two electric leads. They are just connector type leads going to the switches. Pluged the leads onto the correct sides of the new latch assembly and reversed the procedure to put the panel back in place.

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

Removed 10 torx head screws from around perimeter of door (two of these screws hold door latch and handle). Unplug two wires from handle assembly and replace old handle with new. Reinstall 10 perimeter screws and job is complete.