This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.
$125.52
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
$255.89
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.
$19.48
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.
$73.93
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Ma...
$14.20
In Stock
Order within the next 1 hr and 56 mins and your part ships today!
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
I thought I had only a water valve problem - both the noise and leak seemed to come from the water valve assembly - but I had two. After replaced the water valve (a job which was easy to do as the assembly was easily accessed from the rear of the machine) the moaning stopped but I was surprised to discover that I had a stream of water pouring from under the machine.
I pulled the front panel (two phillips head screws needed to be removed) and raised opened the top assembly after removing two hex screws. (The diagram on PartSelect.com was helpful in understanding what I had to deal with).
I observed the fill action, and found that the water was leaking from the slots in the fill nozzle sleeve, in the water injector hose line. (The new inlet water valves had increased the pressure at the fill nozzle and increased the leak from that point which I had not suspected to be the source of the leaking water).
The basic problem was that the rubber valve sleeve had shrunk in length and was no longer flexible, allowing water to come out of the sleeve slots. I ordered an injector nozzle and valve and installed them in the original sleeve bracket in just a few minutes (two clamps had to be loosened, and the hose sections pulled back to insert the valve and nozzle assembly). (I had also ordered a replacement bracket just in case the old one might break, but it was not the correct part and the old one was fine.)
I checked for leaks and closed up the machine. Problems solved! It is now both quiet and leak-free.
(Moral, open the machine and check the nozzle for leaks - even if you suspect only the water valve assembly. The nozzle valve is located above the water valve and its leaks drop onto the water valve, making it look like the water valve assembly is the source of the leak.)
Firstly, remove ac power from washer! After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!
