Jenn-Air Refrigerator Drawers and Glides

This manufacturer-approved Refrigerator Pantry End Cap Kit, also known as the Refrigerator Drawer Support, is a kit containing all parts of the Pantry End Cap. It snaps into place on the appliance’s pantry drawer to help contain the items inside and to keep your refrigerator door from sliding all the way out. It is rated as "medium" difficulty to install, is constructed of plastic and comes in white. If broken or missing, the pantry drawer will not stay in place and the part should be replaced. Refer to your user manual and model number to ensure this is the correct part for you. This kit includes both the right and left side end caps, as well as the pins that will hold them in place. To replace an end cap, remove the three screws holding it in place. Then, remove the pin and end cap, replacing the old end cap with the new end cap. In the past, the left and right end caps were sold separately, but the part has been updated and now includes both sides. The part is sold as a kit, and unfortunately, as such none of the parts are available individually.

This OEM Center Rail is a white plastic part which supports the crisper frame, which holds the crisper. Fifteen inches long and white in colour, if broken, the support may no longer hold properly. Refer to your model number and user manual to see if this part will be right for your appliance. This part is a very easy repair which only takes a few minutes and does not require any tools. Just slide the crisper drawers out, lift out the glass shelf, slide the new rale into place and replace the glass shelf and crisper drawers. This part is sold individually and not as part of a set.

The crisper drawer in your refrigerator is used for storing various items. If you notice that your current crisper drawer is damaged, you may need to replace it. You may notice that your refrigerator door does not open or close properly, which is a sign that your crisper drawer is damaged. This crisper drawer is made of clear plastic. This part is sold individually and does not come with the plastic faceplate on it. If your current crisper has one, you will need to remove it and transfer it to the new crisper. NOTE: As per the manufacture the crisper drawer has been updated from the original. A new crisper cover may need to be purchased for the drawers to work. Factory dimensions - 12.847" Depth X 15.217" Width X 6.93 High.

This part mounts on the wall and is used to support the pantry drawer.

Sold individually.

Sold individually. Crisper drawer is an original equipment manufacturer (OEM) part that fits some bottom-freezer Kenmore, Amana, Crosley, Jenn-Air, KitchenAid, Maytag and Whirlpool refrigerators. The crisper drawer is approximately 6-7/8-inches tall, 14-inches wide and 15-inches deep.

This is a replacement end cap for your refrigerator pantry drawer. The pantry drawer has an endcap on either side, which encloses the drawer. This end cap is for the left side of the pantry drawer only. Make sure you need the left side end cap before you order this part. This part is made of white plastic, and will fit into position on the left side of the pantry drawer. This part is approximately 20 inches wide and 7 inches tall. It is an OEM part sourced directly from the manufacturer.

This part is the replacement for the end cap on your refrigerator pantry drawer. Your pantry drawer will have two end caps; one for the right side and one for the left. This is the end cap for the right-hand side, and is sold separately from the left end cap. The part is made of white plastic and is an OEM part sourced directly from the manufacturer. To remove the old pantry drawer end cap, simply remove the pantry drawer and disconnect the end cap. Replace it with a new one, and slide the pantry drawer back into place.

This part is the replacement pantry drawer cover for your refrigerator. It is made of white and clear plastic and is approximately 31 inches long and 7 inches wide. The pantry drawer cover is found at the front of the pantry drawer, and it is tapered in the middle, so you can grip the drawer and slide it in and out. The most common reason to replace the pantry drawer cover is if it is broken or missing. This part is sold individually and is an OEM part sourced directly from the manufacturer.