Inglis Cooktop Parts

Inglis Cooktop Chrome Drip Bowl - 8 Inch

★★★★★

★★★★★

23 Reviews

This manufacturer-certified drip bowl is also known as a drip pan, and it is designed for use with cooktops and ranges. It sits below 8-inch burner elements and catches drips and spills from the cookware on the burner. The diameter of the drip bowl is approximately 10 inches. This replacement might appear slightly different, but it will fit your appliance. You will need no tools to complete this repair. Simply remove the burner element, remove the old bowl, line up the hole on the new bowl with the terminal block and drop it into place. Make sure the bowl is flat before reinstalling the element. While you have the element out you should inspect the terminals for corrosion, damage, or discolouration. If you notice any of those things you should also replace the element and terminal block. You will need to replace your drip bowl if it is lost, damaged, or can no longer be cleaned. This replacement part is sold individually. To extend the life of your new drip bowl we recommend you clean it regularly with soap and water. We recommend only using the recommended drip bowl for your appliance; generic versions will not fit properly which could affect the performance of your elements and cause long-term damage.

Inglis Cooktop Chrome Drip Bowl - 6"

★★★★★

★★★★★

20 Reviews

This drip bowl is sold individually. This part is located beneath the element and catches spills from cooking.

Inglis Cooktop Drip Bowl - 8"

★★★★★

★★★★★

18 Reviews

This drip bowl is located beneath the element and catches any spills. It is sold individually and has a diameter of approximately 10 inches.

Inglis Cooktop Drip Bowl - 6 Inch This drip bowl, also known as the drip pan or burner bowl, is 6 inches in internal diameter to match the burner, but actually measures closer to 8 inches in total diameter to its outer edges. This authentic manufacturer-approved part is used to catch spills from cooking on the top burner. If your bowls are getting stained, dirty, or rusted, this replacement can solve it. First, remove the element from the stove top, and pull out the old drip pan. Insert the new bowl and make sure it is aligned to where the element is plugged in. Lastly, you can put the element back in. For safety precautions, make sure to unplug the range from the power source and wait until the surface is cool before replacing this part. This part is sold individually, if you are replacing more than one drip bowl on your stove at once, you will need to account for this. To replace, simply pull the old surface elements and burner bowls off, give everything a thorough clean, and install the new parts with no tools necessary.

Inglis Cooktop Terminal Block Kit

★★★★★

★★★★★

45 Reviews

This surface burner terminal block kit comes with interchangeable mounting brackets, terminal box, ceramic wire nuts, heat shrink protective tubing and wires.

Inglis Cooktop Drip Bowl - 6 Inch

★★★★★

★★★★★

9 Reviews

This part has been substituted by the manufacturer and has a hole in the center. It no longer has a solid bottom.

Inglis Cooktop Drip Bowl - 8 Inch

★★★★★

★★★★★

1 Review

This part is located beneath the element and catches any spills.

Inglis Cooktop Knob - Chrome

★★★★★

★★★★★

24 Reviews

This chrome OEM control knob measures 1 1/2" in diameter. It easily attaches onto the D-shaped shaft in order to allow controls to be used. Refer to your model number and user manual to ensure this part is correct for you. This part is sold individually. We recommend replacing all control knobs for your unit at the same time, as they wear at a consistent rate to one another. This very easy repair should only take a few moments to complete; just slide the old knob off the shaft and the new one on.

Inglis Cooktop Burner Knob

★★★★★

★★★★★

16 Reviews

Sold individually. This knob accepts a D-shaped shaft.

Inglis Cooktop Knob - Chrome

★★★★★

★★★★★

2 Reviews

This authentic OEM knob is supplied by the original manufacturer for use with GE cooktops. It provides a comfortable grip for adjusting burner settings and is made from durable plastic to ensure long-lasting performance. Over time, the knob may wear out or become damaged, requiring replacement. Installation is simple—just pull the old knob off the shaft and press the new one firmly into place. This part is sold individually. For proper placement and installation, refer to your model’s diagrams.