Models > PAVT144AWW

PAVT144AWW Maytag Washer - Overview

Find Parts and Repair Help for PAVT144AWW.

If you know the repair part that will fix your washer you can search through the list of all parts for PAVT144AWW or you can narrow down the list by entering in the part description or name. If you know where the part is located on the PAVT144AWW you can search for it by selecting one of the section diagrams below. We've also put together a list of symptoms common to your washer so you can find the part you need based on the problem you are having. We've included all of our repair videos that apply to PAVT144AWW to help you easily complete your repair. You can search through the installation instructions, written by our helpful PartSelect.ca customers, to find more information on your repair.




Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?

CAD$8.58


Lid Hinge Pin

PartSelect Number PS2037923
Manufacturer Part Number 35-2045


CAD$5.46


Snubber Ring

PartSelect Number PS1792928
Manufacturer Part Number 21002026


CAD$80.16


Drain Pump

PartSelect Number PS2347193
Manufacturer Part Number 35-6780

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.


CAD$16.88


Drive Belt

PartSelect Number PS2018741
Manufacturer Part Number 21352320

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.


CAD$4.66


Lid Hinge

PartSelect Number PS2037922
Manufacturer Part Number 35-2044

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.


CAD$41.61


Transmission Pulley and Bearing Kit

PartSelect Number PS2003651
Manufacturer Part Number 12002213

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are not available separately - only available in this kit. A worn bearing causes slow or no spin.


CAD$33.90


Suspension Springs - Kit of 6

PartSelect Number PS2004049
Manufacturer Part Number 12002773


CAD$3.10


Hose Clamp

PartSelect Number PS380193
Manufacturer Part Number 596669


CAD$3.24


Suspension Spring Hook

PartSelect Number PS2017707
Manufacturer Part Number 21001166


CAD$3.10


Screw

PartSelect Number PS2026498
Manufacturer Part Number 25-7893

This screw is a metallic screw that is used for many clothes washers.




Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The belt and pulley on the drive motor broke

Customer: Michael from Warminster PA
Difficulty: Really easy
Time to Complete: 30 - 60 mins
Tools Required: Screw drivers, Wrench(Adjustable)
84 of 106 people found this instruction helpful
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the p... read more

EXCESSIVE Banging, shaking and squeaking while on Spin Cycle

Customer: robert from simpsonville SC
Difficulty: Easy
Time to Complete: 30 - 60 mins
Tools Required: Nutdriver, Pliers
63 of 66 people found this instruction helpful
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small contain... read more

bearing on water pump siezed

Customer: kevin from rochester NY
Difficulty: Really easy
Time to Complete: Less than 15 mins
Tools Required: Nutdriver, Pliers
55 of 57 people found this instruction helpful
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!! read more