This door gasket can be installed by simply pressing it into the channel around the door. This dishwasher door gasket, or door seal, allows the dishwasher door to have an airtight seal when closing th...
This impeller rotates and is used to force water up through to the spray arm.
$66.64
In Stock
Questions And Answers for MDB7100AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathy
January 9, 2020
How much would the motor cost for this dishwasher?
For model number MDB7100AWW
Hello Kathy, thank you for your question. The motor and pump for this unit is PartSelect Number: PS2340847. Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Donna
September 24, 2021
How do I find a top rack to replace mine due to rust and holes from rust
For model number MDB7100AWW
Hello Donna, thank you for writing. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2099053. We hope this helps.
The 3 sec. light is on and I can not start the dishwasher.
How do I clear the 3 sec. light? When I toush on the the 3 sec light it will flash,
when I release, it goes back to solid red light.
For model number MDB7100AWW
Hello George, thank you for reaching out. If your dishwasher is not starting, we suggest that you check the door switches and holder assembly, part number PS2099645, door latch handle, part number PS11747644, and the main control board, part number PS11747721. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
howdy, I am guessing I need a new control board. Turned on washer last night started to operate (heavy wash) had water then it would not cycle through. Tried again today on light wash went from 95 minutes to 65 in wash cycle then stopped. I still have water lying in bottom of washer. Thanks for you response. Randy
For model number MDB7100AWW
Hi Randall,
Thank you for your question. If your dishwasher will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door latch and switches, the latch handle, and the electronic control board. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
Hello Joseph, thank you for contacting us. Your model does not have a thermal fuse, but it does have a high-limit thermostat that turns off the heating element if it overheats. The high-limit thermostat is generally located at the bottom of the dishwasher. It can be accessed from under the dishwasher. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Took out about 7 torx screws to remove the inner door liner. Discovered evidence of leak coming from the sop dispenser latch, and noticed the grommet had turned soft and was torn. The grommet is only about 1" square. Used nut driver to remove two screws to remove latch assembly. Slipped old grommet off and put new one on, and reattached the latch. The foam seal at the bottom of the door looked worn, so we replaced it with weatherstripping from home improvement store. The main door seal was brittle, so we replaced it too - just grab an end and pull the old one out. The new one was installed by starting at one end and we just pushed it in place. We used a nut-driver to push it in - we were afraid a screwdriver might damage it. The new door seal required us to latch the door to get it to stay closed the fist couple of days, but now it has loosened up a bit and works as expected. And NO MORE LEAKS. Cost is much less than a new unit!
I opened the end stop of the rack, replaced the roller, and put the end stop back on. I can't believe I paid the repairman the last time $125????? An he put in a regular screw that rusted and broke the roller. Took me 3 minutes! Thanks
I ordered two clips just in case. Turns out I needed both of them. Since I hadn't seen the adjustable tines installed, it took some time to figure out how to put the assembly together.
For some reason I had the dishwasher for 7 years before it occurred to me to order the replacement parts. It's much more efficient to use with the adjustable tines properly installed as I can load approximately 25% more plates than before.